- 您现在的位置：买卖IC网 > PDF目录14485 > MCP1602-330I/MS (Microchip Technology)IC REG BUCK SYNC 3.3V 0.5A 8MSOP PDF资料下载
参数资料
| 型号： | MCP1602-330I/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 3.3V 0.5A 8MSOP |
| 标准包装： | 100 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 2.7 V ~ 5.5 V |
| 频率 - 开关： | 2MHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 供应商设备封装： | 8-MSOP |
| 产品目录页面： | 668 (CN2011-ZH PDF) |
MCP1602
4.4
Soft Start
4.7
Enable/Disable Control
The output of the MCP1602 is controlled during start-
up. This control allows for a very minimal amount of
V OUT overshoot during start-up from V IN rising above
the UVLO voltage or SHDN being enabled.
The SHDN pin is used to enable or disable the
MCP1602. When the SHDN pin is pulled low, the
device is disabled. When pulled high the device is
enabled and begins operation provided the input
voltage is not below the UVLO threshold or a fault
4.5
Overtemperature Protection
condition exists.
Overtemperature protection circuitry is integrated in the
MCP1602. This circuitry monitors the device junction
4.8
Undervoltage Lockout (UVLO)
temperature and shuts the device off if the junction tem-
perature exceeds the typical 150 o C threshold. If this
threshold is exceeded, the device will automatically
restart once the junction temperature drops by
approximately 10 o C. The soft start is reset during an
overtemperture condition.
The UVLO feature uses a comparator to sense the
input voltage (V IN ) level. If the input voltage is lower
than the voltage necessary to properly operate the
MCP1602, the UVLO feature will hold the converter off.
When V IN rises above the necessary input voltage, the
UVLO is released and soft start begins. Hysteresis is
built into the UVLO circuit to compensate for input
4.6
Overcurrent Protection
impedance. For example, if there is any resistance
between the input voltage source and the device when
Cycle-by-cycle current limiting is used to protect the
MCP1602 from being damaged when an external short
circuit is applied. The typical peak current limit is
700 mA. If the sensed current reaches the 700 mA
limit, the P-Channel MOSFET is turned off, even if the
output voltage is not in regulation. The device will
attempt to start a new switching cycle when the internal
oscillator sets the internal RS latch.
? 2007 Microchip Technology Inc.
it is operating, there will be a voltage drop at the input
to the device equal to I IN x R IN . The typical hysteresis
is 200 mV.
DS22061A-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| 380LX681M350A052 | CAP ALUM 680UF 350V 20% SNAP |
| VI-B1H-EW-F3 | CONVERTER MOD DC/DC 52V 100W |
| VI-B1H-EW-F2 | CONVERTER MOD DC/DC 52V 100W |
| LGU1K682MELC | CAP ALUM 6800UF 80V 20% SNAP |
| 2300HT-121-H-RC | INDUCTOR TOROID 120UH 15% HORZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1602-ADJI/MF | 功能描述:开关变换器、稳压器与控制器 20MHz 05A Synch-Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP1602-ADJI/MS | 功能描述:开关变换器、稳压器与控制器 20MHz 05A Synch-Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP1602EV | 功能描述:电源管理IC开发工具 MCP1602 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1602T-080I/MF | 功能描述:开关变换器、稳压器与控制器 20MHz 05A Synch-Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP1602T-080I/MS | 功能描述:开关变换器、稳压器与控制器 20MHz 05A Synch-Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。