参数资料
型号: MCP1603T-080I/OS
厂商: Microchip Technology
文件页数: 13/26页
文件大小: 0K
描述: IC REG BUCK SYNC 0.8V TSOT23-6
标准包装: 3,000
类型: 降压(降压)
输出类型: 固定
输出数: 1
输出电压: 0.8V
输入电压: 2.7 V ~ 5.5 V
PWM 型: 电流模式
频率 - 开关: 2MHz
电流 - 输出: 500mA
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: SOT-23-5 细型,TSOT-23-5
包装: 带卷 (TR)
供应商设备封装: TSOT-23-5
配用: MCP1603RD-TNY-ND - REFERENCE DESIGN FOR MCP1603
MCP1603EV-ND - BOARD EVAL BUCK CONV MCP1603
MCP1603
4.3
Soft Start
4.6
Enable/Disable Control
The output of the MCP1603 is controlled during start-
up. This control allows for a very minimal amount of
V OUT overshoot during start-up from V IN rising above
the UVLO voltage or SHDN being enabled.
The SHDN pin is used to enable or disable the
MCP1603. When the SHDN pin is pulled low, the
device is disabled. When pulled high the device is
enabled and begins operation provided the input
voltage is not below the UVLO threshold or a fault
4.4
Overtemperature Protection
condition exists.
Overtemperature protection circuitry is integrated in the
MCP1603. This circuitry monitors the device junction
4.7
Undervoltage Lockout (UVLO)
temperature and shuts the device off, if the junction
temperature exceeds the typical 150°C threshold. If
this threshold is exceeded, the device will automatically
restart once the junction temperature drops by
approximately 10°C. The soft start is reset during an
overtemperture condition.
4.5 Overcurrent Protection
Cycle-by-cycle current limiting is used to protect the
MCP1603 from being damaged when an external short
circuit is applied. The typical peak current limit is
860 mA. If the sensed current reaches the 860 mA
limit, the P-Channel MOSFET is turned off, even if the
output voltage is not in regulation. The device will
attempt to start a new switching cycle when the internal
oscillator sets the internal RS latch.
? 2007 Microchip Technology Inc.
The UVLO feature uses a comparator to sense the
input voltage (V IN ) level. If the input voltage is lower
than the voltage necessary to properly operate the
MCP1603, the UVLO feature will hold the converter off.
When V IN rises above the necessary input voltage, the
UVLO is released and soft start begins. Hysteresis is
built into the UVLO circuit to compensate for input
impedance. For example, if there is any resistance
between the input voltage source and the device when
it is operating, there will be a voltage drop at the input
to the device equal to I IN x R IN . The typical hysteresis
is 140 mV.
DS22042A-page 13
相关PDF资料
PDF描述
MCP1612-ADJI/MF IC REG BUCK SYNC ADJ 1A 8DFN
MCP1624T-I/MC IC BOOST SYNC REG PWM/PFM 8DFN
MCP1630-E/MS IC REG CTRLR BST FLYBK ISO 8MSOP
MCP16301T-I/CHY IC REG BUCK ADJ 0.6A SOT23-6
MCP1631-E/ST IC REG CTRLR ISO PWM CM 20-TSSOP
相关代理商/技术参数
参数描述
MCP1603T-120I/MC 功能描述:开关变换器、稳压器与控制器 2.0MHz 0.5A Synch- Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
MCP1603T-120I/OS 功能描述:开关变换器、稳压器与控制器 2.0MHz 0.5A Synch- Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
MCP1603T-150I/MC 功能描述:开关变换器、稳压器与控制器 2.0MHz 0.5A Synch- Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
MCP1603T-150I/OS 功能描述:开关变换器、稳压器与控制器 2.0MHz 0.5A Synch- Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
MCP1603T-180I/MC 功能描述:开关变换器、稳压器与控制器 2.0MHz 0.5A Synch- Buck PFM/PWM Reg RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel