参数资料
型号: MCP1612T-ADJI/MF
厂商: Microchip Technology
文件页数: 13/22页
文件大小: 0K
描述: IC REG BUCK SYNC ADJ 1A 8DFN
标准包装: 3,300
类型: 降压(降压)
输出类型: 可调式
输出数: 1
输出电压: 0.8 V ~ 5 V
输入电压: 2.7 V ~ 5.5 V
PWM 型: 电流模式
频率 - 开关: 1.4MHz
电流 - 输出: 1A
同步整流器:
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 8-VDFN 裸露焊盘
包装: 带卷 (TR)
供应商设备封装: 8-DFN-EP(3x3)
MCP1612
Solving for C:
5.2.6
COMPENSATION COMPONENTS
C = I C × -----------
Δ t
Δ V C
Where:
I C = peak-to-peak ripple current
Δ t = on-time of P-channel MOSFET
Δ V C = output ripple voltage
An internal transconductance error amplifier is used to
compensate the buck converter. An external resistor
(R C ) and capacitor (C C ), connected between COMP
and GND, are all that is needed to provide a high-
bandwidth loop.
Table 5-1 identifies values for R C and C C for standard
buck inductor (L) and output capacitor (C OUT ) values.
There will also be some ripple voltage caused by the
TABLE 5-1:
R C and C C VALUES
ESR of the capacitor. The ripple is defined as follows.
EQUATION 5-7:
V ESRRIPPLE = ESR × I C
L
3.3 μH
2.2 μH
C OUT
10.0 μF
4.7 μF
R C
25 k Ω
10 k Ω
C C
1000 pF
1000 pF
For this example:
5.3
Printed Circuit Board (PCB)
Layout
I C = 165 mA
C = 4.7 μF
Δ t = 260 ns
ESR = 8 m Ω
Δ V C = (260 ns x 165 mA)/4.7 μF
Δ V C = 9.13 mV
V ESRRIPPLE = 8 m Ω x 165 mA
V ESRRIPPLE = 1.32 mV
Δ V OUT = Δ V C + V ESRRIPPLE
Δ V OUT = 9.13 mV + 1.32 mV
Δ V OUT = 10.45 mV
The MCP1612 is capable of switching over 1A at
1.4 MHz. As with all high-frequency switching power
supplies, good PCB layout techniques are essential to
prevent noise generated by the switching power-train
from interfering with the sensing circuitry.
There are two ground pins (P GND and A GND ) on the
MCP1612 to separate the large-signal ground current
from the small-signal circuit ground. These two
grounds should be kept separate, only connecting near
the input bulk capacitor.
Care must also be taken to minimize the length and
loop area of the large signal connections. Components
connected to this loop consist of the input bulk
5.2.4
INPUT CAPACITOR
capacitor, V IN , P GND and L X pins of the MCP1612, the
buck inductor and the output filter capacitor.
For the buck topology, the input current is pulled from
the source and the input capacitor in pulses. The size
of the input capacitor will determine the amount of
current pulled from the source. For most applications,
a 10 μF ceramic capacitor connected between the
MCP1612’s V IN and P GND is recommended to filter the
current pulses. Less capacitance can be used for
applications that have low source impedance. The
ripple current rating for ceramic capacitors are typically
very high due to their low loss characteristics. Low-cost
electrolytic capacitors can be used, but their ripple
current rating should not be exceeded.
5.2.5
V CC INPUT
The V CC input is used to bias the internal MCP1612
circuitry. A 10 Ω resistor is recommended between the
unregulated inputs V IN and V CC , along with a 0.1 μF
capacitor to ground to help isolate the V CC pin from the
switching noise.
? 2005 Microchip Technology Inc.
DS21921B-page 13
相关PDF资料
PDF描述
CGS183U025R4C CAP ALUM 18000UF 25V SCREW
GCC28DREI CONN EDGECARD 56POS .100 EYELET
CGS123U030R4C CAP ALUM 12000UF 30V SCREW
EEC50DRTF CONN EDGECARD 100PS DIP .100 SLD
GSM22DRTS CONN EDGECARD 44POS DIP .156 SLD
相关代理商/技术参数
参数描述
MCP1612T-ADJIMS 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Single 1A, 1.4 MHz Synchronous Buck Regulator
MCP1612T-I/MF 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Single 1A, 1.4 MHz Synchronous Buck Regulator
MCP1612T-I/MS 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Single 1A, 1.4 MHz Synchronous Buck Regulator
MCP1614-150X120I/ER 功能描述:直流/直流开关转换器 1.4MHz 1A Synch-Buck RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
MCP1614-150X120I/QR 制造商:Microchip Technology Inc 功能描述:DUAL-1.4MHZ, 1.0A, SYNCH-BUCK REGULATOR, ADJ. OUTPUT - Rail/Tube