- 您现在的位置：买卖IC网 > PDF目录1852 > MCP16301T-I/CHY (Microchip Technology)IC REG BUCK ADJ 0.6A SOT23-6 PDF资料下载
参数资料
| 型号： | MCP16301T-I/CHY |
| 厂商： | Microchip Technology |
| 文件页数： | 13/38页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.6A SOT23-6 |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 2 V ~ 15 V |
| 输入电压： | 4 V ~ 30 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 500kHz |
| 电流 - 输出： | 600mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 包装： | 标准包装 |
| 供应商设备封装： | SOT-23-6 |
| 其它名称： | MCP16301T-I/CHYDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页
MCP16301
4.2.2
PEAK CURRENT MODE CONTROL
4.2.4
HIGH SIDE DRIVE
The MCP16301 integrates a Peak Current Mode
Control architecture, resulting in superior AC regulation
while minimizing the number of voltage loop
compensation components, and their size, for
integration. Peak Current Mode Control takes a small
portion of the inductor current, replicates it and
compares this replicated current sense signal with the
output of the integrated error voltage. In practice, the
inductor current and the internal switch current are
equal during the switch-on time. By adding this peak
current sense to the system control, the step-down
power train system is reduced from a 2 nd order to a 1 st
order. This reduces the system complexity and
increases its dynamic performance.
For Pulse-Width Modulation (PWM) duty cycles that
exceed 50%, the control system can become bimodal
where a wide pulse followed by a short pulse repeats
instead of the desired fixed pulse width. To prevent this
mode of operation, an internal compensating ramp is
4.2.3 PULSE-WIDTH MODULATION
(PWM)
The internal oscillator periodically starts the switching
period, which in MCP16301’s case occurs every 2 μs
or 500 kHz. With the integrated switch turned on, the
inductor current ramps up until the sum of the current
sense and slope compensation ramp exceeds the inte-
grated error amplifier output. The error amplifier output
slews up or down to increase or decrease the inductor
peak current feeding into the output LC filter. If the reg-
ulated output voltage is lower than its target, the invert-
ing error amplifier output rises. This results in an
increase in the inductor current to correct for errors in
the output voltage. The fixed frequency duty cycle is
The MCP16301 features an integrated high-side
N-Channel MOSFET for high efficiency step-down
power conversion. An N-Channel MOSFET is used for
its low resistance and size (instead of a P-Channel
MOSFET). The N-Channel MOSFET gate must be
driven above its source to fully turn on the transistor. A
gate-drive voltage above the input is necessary to turn
on the high side N-Channel. The high side drive voltage
should be between 3.0V and 5.5V. The N-Channel
source is connected to the inductor and Schottky diode,
or switch node. When the switch is off, the inductor cur-
rent flows through the Schottky diode, providing a path
to recharge the boost cap from the boost voltage
source, typically the output voltage for 3.0V to 5.0V out-
put applications. A boost-blocking diode is used to pre-
vent current flow from the boost cap back into the
output during the internal switch-on time. Prior to
startup, the boost cap has no stored charge to drive the
switch. An internal regulator is used to “pre-charge” the
boost cap. Once pre-charged, the switch is turned on
and the inductor current flows. When the switch turns
off, the inductor current free-wheels through the
Schottky diode, providing a path to recharge the boost
cap. Worst case conditions for recharge occur when
the switch turns on for a very short duty cycle at light
load, limiting the inductor current ramp. In this case,
there is a small amount of time for the boost capacitor
to recharge. For high input voltages there is enough
pre-charge current to replace the boost cap charge. For
input voltages above 5.5V typical, the MCP16301
device will regulate the output voltage with no load.
After starting, the MCP16301 will regulate the output
voltage until the input voltage decreases below 4V. See
voltage, output voltage and load.
terminated when the sensed inductor peak current,
4.2.5
ALTERNATIVE BOOST BIAS
summed with the internal slope compensation,
exceeds the output voltage of the error amplifier. The
PWM latch is set by turning off the internal switch and
preventing it from turning on until the beginning of the
next cycle. An overtemperature signal, or boost cap
undervoltage, can also reset the PWM latch to asyn-
chronously terminate the cycle.
? 2011 Microchip Technology Inc.
For 3.0V to 5.0V output voltage applications, the boost
supply is typically the output voltage. For applications
with 3.0V < V OUT < 5.0V, an alternative boost supply
can be used.
Alternative boost supplies can be from the input, input
derived, output derived or an auxiliary system voltage.
For low voltage output applications with unregulated
input voltage, a shunt regulator derived from the input
can be used to derive the boost supply. For
applications with high output voltage or regulated high
input voltage, a series regulator can be used to derive
the boost supply.
DS25004A-page 13
相关PDF资料 |
PDF描述 |
|---|---|
| MCP1631-E/ST | IC REG CTRLR ISO PWM CM 20-TSSOP |
| MCP1631HVT-500E/ST | IC REG CTRLR ISO PWM CM 20-TSSOP |
| MCP1631VHVT-330E/ST | IC REG CTRLR ISO PWM VM 20-TSSOP |
| MCP16322T-ADJE/NG | IC REG BUCK SYNC ADJ 2A 16-VQFN |
| MCP16323T-500E/NG | IC REG BUCK SYNC 5V 3A 16-VQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1630DM-DDBK1 | 功能描述:电源管理IC开发工具 MCP1630 1A Bias Sply Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1630DM-DDBK4 | 功能描述:电源管理IC开发工具 MCP1630 1A Bias Sply Demo Board RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1630DM-DDBS1 | 功能描述:电源管理IC开发工具 MCP1630 Auto Input Boost Demo Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1630DM-DDBS2 | 功能描述:电源管理IC开发工具 MCP1630 Coupled Ind Boost Demo Bd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| MCP1630DM-LED2 | 功能描述:电源管理IC开发工具 MCP1630 Boost Mode LED Drvr Demo Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。