- 您现在的位置：买卖IC网 > PDF目录15511 > MCP1631HV-500E/SS (Microchip Technology)IC REG CTRLR ISO PWM CM 20-SSOP PDF资料下载
参数资料
| 型号： | MCP1631HV-500E/SS |
| 厂商： | Microchip Technology |
| 文件页数： | 40/54页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR ISO PWM CM 20-SSOP |
| 标准包装： | 67 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 2MHz |
| 占空比： | 10% |
| 电源电压： | 3.5 V ~ 16 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 668 (CN2011-ZH PDF) |
| 配用： | MCP1631RD-DCPC1-ND - REF DES BATT CHARG OR LED DRIVER MCP1631RD-MCC2-ND - REFERENCE DESIGN MCP1631HV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页当前第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
MCP1631HV Multi-Chemistry Battery Charger Reference Design
30. EE_CHEMISTRY_DEFAULT = LiIon
Default Chemistry.
31. EE_NUMBER_OF_CELLS_DEFAULT = 2
Default number of cells value.
32. EE_LION_CAL_VOLTAGE_DEFAULT = ((int)((float)(4200.00 /
BATTERY_MV_PER_BIT)))
Default Lithium Ion battery calibration value.
33. EE_CHARGE_TIMEOUT_DEFAULT = (5*60*60)
Maximum charging time.
NiMH = Use (C rating in mAh/Charge Current) + 1hr Topoff + 0.25hr pre-condition)
*60 sec * 60 min
Lithium Ion = Use about 2.5 * (C rating in mAh/Charge Current) * 60 sec * 60 min
34. OSCILLATOR_DUTY_CYCLE = 25
Oscillator duty cycle in percent. Must be in 1/16th intervals due to 4 bit counter.
35. RS232_DATALOGGING = ENABLED
Set to ENABLE for logging data out to USART port and PICkit TM Serial Analyzer.
Set to DISABLED to remove logging code.
36. THERMISTOR_SUPPORT = ENABLED
Set to ENABLE for thermistor support. Used for NiMH and NiCD charging.
Set to DISABLED to remove thermistor code.
37. LED_DRIVER_SUPPORT = ENABLED
Set to ENABLE for LED driver support.
Set to DISABLED to remove LED driver code.
38. LED_DRIVER_OVER_VOLTAGE = ((int)(3600.0 / BATTERY_MV_PER_BIT))
Set this value to the voltage in mV that is the absolute limit of each single LED.
The system will go into overvoltage shutdown mode if the output voltage exceeds
this value times the number of LED series connected cells being driven.
39. LED_DRIVER_CONDITION_CURRENT =
((int)(10.0/BATTERY_MA_PER_BIT))
LED conditioning (startup) current.
40. LED_DRIVER_CONDITION_VOLTAGE = ((int)(0.0/ BATTERY_MV_PER_BIT))
LED conditioning voltage is 0 volts. No conditioning required.
41. LED_DRIVER_CURRENT = ((int)(300.0 / BATTERY_MA_PER_BIT))
LED Driver current maximum value. This is the upper current limit value that the
driver will deliver to the LED output.
42. LED_DRIVER_OVTEMP_SETPOINT = ((float)(THERMISTOR_OHMS_45C))
Optional LED overtemperature limit may be used to limit LED temperature.
Set LED_DRIVER_OVTEMP_SETPOINT to one of the Thermistor Ohms
definitions for the desired shutdown temperature.
43. MAX_LED_CELLS = 2
Maximum number of 1W LED cells in series that will be driven by the driver
output.
DS51791A-page 36
? 2009 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP1630V-E/MS | IC REG CTRLR BST FLYBK ISO 8MSOP |
| UWH1V101MCL1GS | CAP ALUM 100UF 35V 20% SMD |
| UWH1H470MCL1GS | CAP ALUM 47UF 50V 20% SMD |
| UWH1E221MCL1GS | CAP ALUM 220UF 25V 20% SMD |
| UWH1C221MCL1GS | CAP ALUM 220UF 16V 20% SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1631HV-E/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631HV-E/SS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631HV-E/ST | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631HVT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
| MCP1631HVT-330E/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:High-Speed, Pulse Width Modulator |
发布紧急采购，3分钟左右您将得到回复。