- 您现在的位置：买卖IC网 > PDF目录15017 > MCP16321T-150E/NG (Microchip Technology)IC REG BUCK SYNC 1.5V 1A 16-VQFN PDF资料下载
参数资料
| 型号： | MCP16321T-150E/NG |
| 厂商： | Microchip Technology |
| 文件页数： | 15/34页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 1.5V 1A 16-VQFN |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 1.5V |
| 输入电压： | 6 V ~ 24 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 电流 - 输出： | 1A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-VFQFN 裸露焊盘 |
| 包装： | 标准包装 |
| 供应商设备封装： | 16-QFN（3x3） |
| 其它名称： | MCP16321T-150E/NGDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
MCP16321/2
4.0
DETAILED DESCRIPTION
4.1.4
ENABLE INPUT
The enable input (EN) is used to disable the device. If
4.1
Device Overview
disabled, the device consumes a minimal current from
The MCP16321/2 is a high-input voltage, step-down
regulator, capable of supplying 1A/2A to a regulated
output voltage from 0.9V to 5V. Internally, the 1 MHz
oscillator provides a fixed frequency, while the Peak
Current Mode Control architecture varies the duty cycle
for output voltage regulation. An internal floating driver
is used to turn the high-side integrated N-Channel
MOSFET on and off. The power for this driver is
derived from an external boost capacitor whose energy
is replenished when the low-side N-Channel MOSFET
the input. Once enabled, the internal soft start controls
the output voltage rate of rise, preventing high-inrush
current and output voltage overshoot. The EN is
internally pulled up or enabled; to disable the converter,
it must be pulled low.
4.1.5 SOFT START
The internal reference voltage rate of rise is controlled
during startup, minimizing the output voltage overshoot
and the inrush current.
is turned on. When the maximum duty cycle
approaches 100%, the boost capacitor is replenished
for 240 ns after every 8 cycles.
4.1.6
OUTPUT OVER VOLTAGE
PROTECTION
4.1.1 INTERNAL REFERENCE VOLTAGE
V REF
For the adjustable version, an integrated precise 0.9V
If the output of the regulator exceeds 103% of the
regulation voltage, the SW outputs will tri-state to
protect the device from damage. This check occurs at
the start of each switching cycle.
reference combined with an external resistor divider
sets the desired converter output voltage. The resistor
4.1.7
INPUT UNDER VOLTAGE LOCKOUT
divider can vary without affecting the control system
gain. High-value resistors consume less current, but
are more susceptible to noise. For the fixed version, an
integrated precise voltage reference is set to the
desired V OUT value and is directly connected to V OUT .
4.1.2 INTERNAL COMPENSATION
An integrated Under Voltage Lockout (UVLO) prevents
the converter from starting until the input voltage is high
enough for normal operation. The converter will
typically start at 5.75V (typical) and operate down to
5.25V (typical). Hysteresis of 500 mV (typical) is added
to prevent starting and stopping during startup, as a
result of loading the input voltage source.
All control system components necessary for stable
operation over the entire device operating range are
4.1.8
MINIMUM DUTY CYCLE
integrated, including the error amplifier and inductor
current slope compensation.
4.1.3 EXTERNAL COMPONENTS
External components consist of:
? Input capacitor
? Output filter (inductor and capacitor)
? Boost capacitor
? Resistor divider (adjustable version only)
The selection of the external inductor, output capacitor,
input capacitor and boost capacitor is dependent upon
the output voltage and the maximum output current.
? 2011 Microchip Technology Inc.
A minimum duty cycle of 70 ns typical prevents the
device from constant switching for high step-down
voltage ratios. Duty cycles less than this minimum will
initiate pulse skipping to maintain output voltage
regulation, resulting in higher output voltage ripple.
Duty cycle for continuous inductor current operation is
approximated by V OUT /V IN . For a 1 MHz switching
frequency or 1 μs period, this results in a 7% duty cycle
minimum. Maximum V IN for continuous switching can
be approximated dividing V OUT by the minimum duty
cycle or 7%. For example, the maximum input voltage
for continuous switching for a 1.5V output is equal to
approximately 21V.
DS22285A-page 15
相关PDF资料 |
PDF描述 |
|---|---|
| ECO-S1EA682CA | CAP ALUM 6800UF 25V 20% SNAP |
| MCP16321T-ADJE/NG | IC REG BUCK SYNC ADJ 1A 16-VQFN |
| MCP16321T-250E/NG | IC REG BUCK SYNC 2.5V 1A 16-VQFN |
| MCP16321T-180E/NG | IC REG BUCK SYNC 1.8V 1A 16-VQFN |
| 70F473AI | CHOKE RF VARNISHED 4700UH 5% |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP16321T-150NG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:24V Input, 1A/2A Output, High Efficiency Synchronous Buck Regulator with Power Good Indication |
| MCP16321T-180E | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:24V Input, 1A/2A Output, High Efficiency Synchronous Buck Regulator with Power Good Indication |
| MCP16321T-180E/NG | 功能描述:开关变换器、稳压器与控制器 1A Synchrouns Buck Switcher 24Vin RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCP16321T-180NG | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:24V Input, 1A/2A Output, High Efficiency Synchronous Buck Regulator with Power Good Indication |
| MCP16321T-250E | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:24V Input, 1A/2A Output, High Efficiency Synchronous Buck Regulator with Power Good Indication |
发布紧急采购，3分钟左右您将得到回复。