- 您现在的位置：买卖IC网 > PDF目录15465 > MCP1650ST-E/MS (Microchip Technology)IC REG CTRLR BST FLYBK PWM 8MSOP PDF资料下载
参数资料
| 型号： | MCP1650ST-E/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST FLYBK PWM 8MSOP |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 850kHz |
| 占空比： | 80% |
| 电源电压： | 2.7 V ~ 5.5 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
| 配用： | MCP1650EV-ND - BOARD EVAL FOR MCP1650,51,52,53 MCP1650DM-LED1-ND - BOARD DEMO FOR MCP165X |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MCP1650/51/52/53
To determine the maximum inductance for
5.2.2
MOSFET SELECTION
Discontinuous Operating mode, multiply the energy
going into the inductor every switching cycle by the
number of cycles per second (switching frequency).
This number must be greater than the maximum input
power.
There are a couple of key consideration’s when
selecting the proper MOSFET for the boost design. A
low R DSON logic-level N-channel MOSFET is
recommended.
The equation for the energy flowing into the inductor is
5.2.2.1
MOSFET Selection Process.
Energy = 1 --- × L × I PK
given below. The input power to the system is equal to
energy times time.
2
2
The inductor peak current is calculated using the
1.
Voltage Rating - The MOSFET drain-to-source
voltage must be rated for a minimum of V OUT +
V FD of the external boost diode. For example, in
the 12V output converter, a MOSFET drain-to-
source voltage rating of 12V + 0.5V is
necessary. Typically, a 20V part can be used for
12V outputs.
I PK = -------- × T ON
equation below:
V IN
L
2.
Logic-Level R DSON - The MOSFET carries
significant current during the boost cycle on
time. During this time, the peak current in the
MOSFET can get quite high. In this example, a
Using a typical inductance of 3.3 μH, the peak current
in the inductor is calculated below:
F SW = 750 kHz
T ON = (1/F SW * Duty Cycle)
I PK (2.8V) = 905 mA
Energy (2.8V) = 1.35 μ-Joules
Power (2.8V) = 1.01 Watts
At 3.8V and below, the converter can boost to 14V
while operating in the Continuous mode.
I PK (3.8V) = 860 mA
Energy at 3.8V = 1.22 μ-Joules
Power = 0.914 Watts
For this example, a 3.3 μH inductor is too large, a
2.2 μH inductor is selected.
F SW = 750 kHz
T ON = (1/F SW * Duty Cycle)
I PK (2.8V) = 1.36A
Energy (2.8V) = 2.02 μ-Joules
Power (2.8V) = 1.52 Watts
I PK (3.8V) = 1.29A
Energy at 3.8V = 1.83 μ-Joules
Power = 1.4 Watts
As the inductance is lowered, the peak current drawn
from the input at all loads is increased. The best choice
of inductance for high boost ratios is the maximum
inductance value necessary while maintaining
discontinuous operation.
For lower boost-ratio applications (3.3V to 5.0V), a
3.3 μH inductor or larger is recommended. In these
cases, the inductor operates in Continuous Current
mode.
DS21876A-page 18
SOT-23 MOSFET was used with the following
ratings:
IRLM2502 N-channel MOSFET
V BDS = 20V (Drain Source Breakdown
Voltage)
R DSON = 50 milli-ohms (V GS = 2.5V)
R DSON = 35 milli-ohms (V GS = 5.0V)
Q G = Total Gate Charge = 8 nC
V GS = 0.6V to 1.2V (Gate Source Threshold
Voltage)
Selecting MOSFETs with lower R DSON is not always
better or more efficient. Lower R DSON typically results
in higher total gate charge and input capacitance, slow-
ing the transition time of the MOSFET and resulting in
increased switching losses.
5.2.3 DIODE SELECTION
The external boost diode also switches on and off at the
switching frequency and requires very fast turn-on and
turn-off times. For most applications, Schottky diodes
are recommended. The voltage rating of the Schottky
diode must be rated for maximum boost output voltage.
For example, 12V output boost converter, the diode
should be rated for 12V plus margin. A 20V or 30V
Schottky diode is recommended for a 12V output appli-
cation. Schottky diodes also have low forward-drop
characteristics, another desired feature for switching
power supply applications.
? 2004 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| EB43-S0C2260W | CONN EDGEBOARD DUAL 44POS 3A |
| 4501R-132M | TOROID PWR LOW PROFILE 200UH SMD |
| MCP1650RT-E/MS | IC REG CTRLR BST FLYBK PWM 8MSOP |
| GBB06DHAS | CONN EDGECARD 12POS R/A .050 SLD |
| ADM6315-31D3ARTRL7 | IC SUPERVISOR OD 3.08V SOT143 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP1651 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:750 kHz Boost Controller |
| MCP1651R-E/MS | 功能描述:热插拔功率分布 w/Lbat Ind UVLO 2V RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MCP1651REMS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:750 kHz Boost Controller |
| MCP1651REUN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:750 kHz Boost Controller |
| MCP1651RT-E/MS | 功能描述:热插拔功率分布 w/Lbat Ind UVLO 2V RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。