- 您现在的位置：买卖IC网 > PDF目录10453 > MCP2003A-E/MD (Microchip Technology)IC TXRX LIN W/VREG 8DFN PDF资料下载
参数资料
| 型号： | MCP2003A-E/MD |
| 厂商： | Microchip Technology |
| 文件页数： | 3/34页 |
| 文件大小： | 0K |
| 描述： | IC TXRX LIN W/VREG 8DFN |
| 产品培训模块： | Microchip MCP20xx LIN Transceiver Overview |
| 标准包装： | 91 |
| 系列： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
2010-2011 Microchip Technology Inc.
DS22230D-page 11
MCP2003/4/3A/4A
1.6
MCP2003/4 and MCP2003A/4A
Difference Details
The differences between the MCP2003/4 and the
MCP2003/4A devices are isolated to the wake-up
functionality. The changes were implemented to make
the device more robust to LIN bus conditions, outside
of the normal operating conditions. The MCP2003/4
will wake-up from Power Down Mode during any LIN
falling edge held low longer than 20us.
In the case where a LIN system is designed to
minimize stand-by current by disconnecting all bus
pull-ups resistors (including the external master pull-
up resistor to VBB), the original MCP2003/4 could
wake up, if the floating bus drifted to a valid low level.
The MCP2003/4A revisions were modified to require a
rising edge after a valid low level. This will prevent an
undesired system wake-up in this scenario, while
maintaining functional capability with the original
version.
It should be noted that the original MCP2003/4 meets
all LIN transceiver specification requirements and
modules can be designed to pass all LIN system
requirements. However, when all bus pull-up resistors
are disconnected, the MCP2003/4 requires the
module designer to write firmware to monitor the LIN
Bus after any wake-up event to prevent the transceiver
from automatically transitioning from Ready mode to
Operational mode.
If the MCP2003/4 is placed into Operational mode,
VBB-LBUS pull-up resistor is automatically connected,
which will raise the LIN bus to a recessive level; then
putting the device to Power-Down mode may cause
LBUS to be floating, and thus wake up all bus nodes.
To prevent this, the designer should insure TXD
(MCP2003) or TXE (MCP2004) is held low until valid
bus activity is verified (see Figure 1-6). This will
ensure the transceiver transitions from Ready mode to
Transmitter Off mode, until bus activity can be verified.
In the case of valid bus activity, the transceiver can
shift to Operation mode, while if there is no bus
activity, the device can be again placed into Power
Down. The design practices needed to accomplish this
are fully detailed in Tech Brief TB3067 - “MCP2003
Power-Down Mode and Wake-Up Handling in Case
of LIN Bus Loss” (DS93067).
The revised MCP2003/4A devices now eliminate the
need for firmware to prevent system wide wake-up.
The revised devices now require a longer valid bus
low (see updated tBDB value in the Specification
tables and FIGURE 2-7: “MCP2003A/4A Remote
Wake-up”), which enables a rising edge detect circuit.
The device will now only wake up after a rising edge,
following a low longer than tBDB. While the module
designer can still hold TXD (MCP2003) or TXE
(MCP2004) low during wake-up, to enter Transmitter
Off mode from Ready mode, it is not required to
prevent an advertent system wake-up.
In addition to the longer tBDB value, the time from
wake-up detect to VREN enable is shortened as
documented in the Specification table.
FIGURE 1-6:
MCP2003/2004 Switching Timing Diagram for the Forced Power-Down Mode
Sequence
TXD
VREN
CS
Ready
Mode
Transmitter OFF
Mode
Power Down
Mode after Master
Sleep instruction
Power Down
Mode
tTx2CS >= 100ns
tCSactive >= 100s
TXD to 0
forced
externally
TXD state depending
on how the Slave
Microcontroller is
powered
LBUS
State
LIN bus
disconnected
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2004AT-E/MD | IC TXRX LIN W/VREG 8DFN |
| VE-BT4-IV-F2 | CONVERTER MOD DC/DC 48V 150W |
| MCP2003AT-E/MD | IC TXRX LIN W/VREG 8DFN |
| VE-27R-IW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
| VI-25F-IU | CONVERTER MOD DC/DC 72V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2003AT-E/MD | 功能描述:LIN 收发器 Stand alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2003AT-E/SN | 功能描述:LIN 收发器 Stand alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2003-E/MD | 功能描述:LIN 收发器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2003-E/P | 功能描述:LIN 收发器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2003-E/SN | 功能描述:LIN 收发器 Stand Alone LIN Transceiver RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。