参数资料
型号: MCP2021PT-330E/MD
厂商: Microchip Technology
文件页数: 8/52页
文件大小: 0K
描述: IC TXRX LIN ON-BOARD VREG 8DFN
产品培训模块: Microchip MCP20xx LIN Transceiver Overview
标准包装: 3,300
系列: *
MCP2021/2/1P/2P
DS22018F-page 16
2005-2012 Microchip Technology Inc.
1.6
Internal Voltage Regulator
1.6.1
5.0V REGULATOR
The MCP2021 has a low-drop-out voltage, positive reg-
ulator capable of supplying 5.00 VDC ±3% at up to
50 mA of load current over the entire operating temper-
ature range of -40°C to +125°C. With a load current of
50 mA, the minimum input to output voltage differential
required for the output to remain in regulation is typi-
cally +0.5V (+1V maximum over the full operating tem-
perature range). Quiescent current is less than 100 A
with a full 50 mA load current when the input to output
voltage differential is greater than +3.00V.
The regulator requires an external output bypass
capacitor for stability. See Figure 2-3 for correct
capacity and ESR for stable operation.
Designed for automotive applications, the regulator will
protect itself from double-battery jumps and up to +43V
load dump transients. The voltage regulator has both
short-circuit and thermal-shut-down protection built in.
Regarding the correlation between VBB, VREG and IDD,
please refer to Figure 1-10 throughFigure 1-12. When
the input voltage (VBB) drops below the differential
needed to provide stable regulation, the output VREG
will track the input down to approximately 3.5V, at
which point the regulator will turn off. This will allow
microcontrollers with internal POR circuits to generate
a clean arming of the POR trip point. The MCP2021 will
then monitor VBB and turn on the regulator when VBB
rises above 5.75, again.
When the input voltage (VBB) drops below the differen-
tial needed to provide stable regulation, the output
VREG) will track the input down to approximately
+4.25V. The regulator will turn off the output at this
point. This will allow PIC microcontrollers with internal
POR circuits to generate a clean arming of the POR trip
point. The regulator output will stay off until VBB is
above +5.75 VDC.
In the start phase, the device must detect at least 5.75V
to initiate operation during power up. In the Power-
Down mode, the VBB monitor will be turned off.
The regulator has a thermal shutdown. If the thermal
protection circuit detects an overtemperature condition,
and the signals TXD and RXD are LOW, or TXD is HIGH,
the regulator will shut down. The recovery from the
thermal shutdown is equal to adequate cooling time.
FIGURE 1-9:
Voltage Regulator Block Diagram.
Note:
The regulator has an overload current
limiting of approximately 100 mA. During a
short circuit, the VREG is monitored. If
VREG is lower than 3.5V, the VREG will turn
off. After a recovery time of about three
milliseconds, the VREG will be checked
again. If there is no short circuit (VREG
>3.5V), the VREG will be switched back on.
Pass
Element
Sampling
Network
Buffer
VREG
VBB
VSS
Fast
Transient
Loop
VREF
相关PDF资料
PDF描述
MCP2021P-500E/MD IC TXRX LIN ON-BOARD VREG 8DFN
MCP2021P-330E/MD IC TXRX LIN ON-BOARD VREG 8DFN
MCP2021T-500E/MD IC LIN TXRX ON-BOARD VREG 8DFN
MCP2021T-330E/MD IC LIN TXRX ON-BOARD VREG 8DFN
MCP2021-500E/MD IC LIN TXRX ON-BOARD VREG 8DFN
相关代理商/技术参数
参数描述
MCP2021PT-500E/MD 功能描述:LIN 收发器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MCP2021PT-500E/SN 功能描述:LIN 收发器 LIN Transceiver with Vreg and LIN RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MCP2021T 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator
MCP2021T-330E/MD 功能描述:LIN 收发器 LIN ver 21 Trnsceivr w/ on-brd 33V Vreg RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8
MCP2021T-330E/MF 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:LIN Transceiver with Voltage Regulator