参数资料
| 型号： | MCP2036-I/P |
| 厂商： | Microchip Technology |
| 文件页数： | 2/30页 |
| 文件大小： | 0K |
| 描述： | IC KEYLESS ENTRY AFE 14-PDIP |
| 标准包装： | 30 |
| 类型： | 传感器接口 |
| 应用： | 模拟 I/O |
| 安装类型： | 通孔 |
| 封装/外壳： | 14-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 14-PDIP |
| 包装： | 管件 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
MCP2036
DS22186B-page 10
2009 Microchip Technology Inc.
The peak-to-peak amplitude of the resulting triangular
waveform, at the coil driver input, is shown in
EQUATION 3-5:
From the previous equation, the designer should
choose values for VPKPK and RIN. Using the equation
above, the value of CIN will be:
EQUATION 3-6:
The amplitude of the pulsed current applied to key
inductors will be:
EQUATION 3-7:
This current produces a pulsed voltage to key inductors
ends. The amplitude of this voltage will be:
EQUATION 3-8:
The total voltage across both the reference and sensor
coils would be double (two series inductors). For a
specific power supply voltage, half of this power supply,
relative to the voltage reference, is available for output
amplifier/detector. Assuming a 30% margin, the
desired gain for the detector should be about:
EQUATION 3-9:
The gain of the amplifier is user-settable, using an
external resistor, RGAIN. The value of that resistor will
be determined using the following equation:
EQUATION 3-10:
With a 10-bit ADC, using oversampling and averaging
techniques, the effective resolution is close to 11 bits.
As shown in AN1239, “Inductive Touch Sensor
Design
”, the typical shift in sensor impedance is typi-
cally 3-4%, so the actual number of counts per press is
typically between 20 and 40 counts. In this way, the
microcontroller firmware could easily detect press
event.
Note:
VPKPK should not exceed specified value
(600mV) for best performance.
Note:
Assuming a power supply of 5V and
VPKPK=500mV, for RIN=3.9KΩ, CIN should
have about 320pF. A 330pF capacitor will
be used.
Note:
For a PWM frequency of 2 MHz and
inductor value of 2.7H, the amplitude of
pulsed voltage will be:
V
PK PK
2
ΔV
=
V
PKPK
V
DD
1
t
–
R
INCIN
------------------
exp
–
1
t
–
R
INCIN
------------------
exp
+
-------------------------------------------
=
C
IN
t
R
IN
ln
V
DD
V
PKPK
–
V
DD
V
PKPK
+
----------------------------------------
-------------------------------------------------------------------
1
2
FR
IN
V
DD
V
PKPK
–
V
DD
V
PKPK
+
----------------------------------------
ln
-------------------------------------------------------------------------------------
=
ΔIV
PK PK
G
DRV
=
G
DRV
- Gain of Coil Driver
ΔUL ΔI
Δt
------
LV
PK PK
G
DRV
2F
=
F
- PWM Frequency
L
- Inductance of Key Inductor
ΔU 10.8mV
=
Note:
For a power supply of 5V and
ΔU = 10mV,
the resulted gain is 81. To obtain this gain,
RGAIN = 820kOhm should be used.
Gain
70%
V
DD
2
-----------
2
ΔU
---------------------------------
=
Gain
R
GAIN/10kOhm
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2036T-I/SL | IC KEYLESS ENTRY AFE 14-SOIC |
| MCP2036-I/SL | IC KEYLESS ENTRY AFE 14-SOIC |
| LFXP6E-3TN144I | IC FPGA 5.8KLUTS 144TQFP |
| AT88SC018-SU-CM-T | IC CRYPTOCOMPANION RF/MEM 8SOIC |
| LFXP6E-4TN144C | IC FPGA 5.8KLUTS 100I/O 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2036T-I/MG | 功能描述:电容触摸传感器 Inductive Sensor AFE RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| MCP2036T-I/ML | 功能描述:电容触摸传感器 Inductive Sensor Ana Front End RoHS:否 制造商:Microchip Technology 电源电压: 通道数量: 封装 / 箱体: 尺寸: 温度范围: |
| MCP2036T-I/SL | 功能描述:电信线路管理 IC Inductive Sensor AFE RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| MCP2050-330E/MQ | 功能描述:LIN 收发器 LIN Transceiver + 3.3V LDO + WWDT RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| MCP2050-330E/SL | 功能描述:LIN 收发器 LIN Transceiver + 3.3V LDO + WWDT RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。