- 您现在的位置：买卖IC网 > PDF目录67985 > MCP23008-E/SS 8 I/O, PIA-GENERAL PURPOSE, PDSO20 PDF资料下载
参数资料
| 型号： | MCP23008-E/SS |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
| 封装： | 0.209 INCH, PLASTIC, SSOP-20 |
| 文件页数： | 7/44页 |
| 文件大小： | 649K |
| 代理商： | MCP23008-E/SS |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
2007 Microchip Technology Inc.
DS21919E-page 15
MCP23008/MCP23S08
1.6.6
CONFIGURATION (IOCON)
REGISTER
The IOCON register contains several bits for
configuring the device:
The Sequential Operation (SEQOP) controls the
incrementing function of the address pointer. If the
address pointer is disabled, the address pointer
does not automatically increment after each byte
is clocked during a serial transfer. This feature is
useful when it is desired to continuously poll
(read) or modify (write) a register.
The Slew Rate (DISSLW) bit controls the slew
rate function on the SDA pin. If enabled, the SDA
slew rate will be controlled when driving from a
high to a low.
The Hardware Address Enable (HAEN) control bit
enables/disables the hardware address pins (A1,
A0) on the MCP23S08. This bit is not used on the
MCP23008. The address pins are always enabled
on the MCP23008.
The Open-Drain (ODR) control bit enables/
disables the INT pin for open-drain configuration.
The Interrupt Polarity (INTPOL) control bit sets
the polarity of the INT pin. This bit is functional
only when the ODR bit is cleared, configuring the
INT pin as active push-pull.
REGISTER 1-6:
IOCON – I/O EXPANDER CONFIGURATION REGISTER (ADDR 0x05)
U-0
R/W-0
U-0
—
SEQOP
DISSLW
HAEN
ODR
INTPOL
—
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
-n = Value at POR
‘1’ = Bit is set
‘0’ = Bit is cleared
x = Bit is unknown
bit 7-6
Unimplemented: Read as ‘0’.
bit 5
SEQOP: Sequential Operation mode bit.
1 = Sequential operation disabled, address pointer does not increment.
0 = Sequential operation enabled, address pointer increments.
bit 4
DISSLW: Slew Rate control bit for SDA output.
1 = Slew rate disabled.
0 = Slew rate enabled.
bit 3
HAEN: Hardware Address Enable bit (MCP23S08 only).
Address pins are always enabled on MCP23008.
1 = Enables the MCP23S08 address pins.
0 = Disables the MCP23S08 address pins.
bit 2
ODR: This bit configures the INT pin as an open-drain output.
1 = Open-drain output (overrides the INTPOL bit).
0 = Active driver output (INTPOL bit sets the polarity).
bit 1
INTPOL: This bit sets the polarity of the INT output pin.
1 = Active-high.
0 = Active-low.
bit 0
Unimplemented: Read as ‘0’.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP23S08T-E/SO | 8 I/O, PIA-GENERAL PURPOSE, PDSO18 |
| MCP23S08-E/SS | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
| MCP23008-E/SO | 8 I/O, PIA-GENERAL PURPOSE, PDSO18 |
| MCP23009-E/MG | 8 I/O, PIA-GENERAL PURPOSE, PQCC16 |
| MCP23009-E/SS | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP23008T-E/ML | 功能描述:接口-I/O扩展器 8bit Input/Output Exp I2C interface RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MCP23008T-E/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Serial Interface |
| MCP23008T-E/SO | 功能描述:接口-I/O扩展器 In/Out I2C int RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MCP23008T-E/SS | 功能描述:接口-I/O扩展器 In/Out I2C int RoHS:否 制造商:NXP Semiconductors 逻辑系列: 输入/输出端数量: 最大工作频率:100 kHz 工作电源电压:1.65 V to 5.5 V 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:HVQFN-16 封装:Reel |
| MCP23009 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Bit I/O Expander with Open-Drain Outputs |
发布紧急采购，3分钟左右您将得到回复。