- 您现在的位置：买卖IC网 > PDF目录11587 > MCP2510-E/P (Microchip Technology)IC CAN CTLR EXTENDED TEMP 18DIP PDF资料下载
参数资料
| 型号： | MCP2510-E/P |
| 厂商： | Microchip Technology |
| 文件页数： | 32/80页 |
| 文件大小： | 0K |
| 描述： | IC CAN CTLR EXTENDED TEMP 18DIP |
| 产品培训模块： | CAN Bus Protection |
| 标准包装： | 25 |
| 控制器类型： | CAN 接口 |
| 接口： | SPI |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 10mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 18-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 18-PDIP |
| 包装： | 管件 |
| 产品目录页面： | 685 (CN2011-ZH PDF) |
| 配用： | DV251001-ND - KIT DEVELOPMENT CAN MCP2510 |
| 其它名称： | MCP2510-E/PR MCP2510-E/PR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
MCP2510
DS21291F-page 38
2007 Microchip Technology Inc.
FIGURE 5-3:
SHORTENING A BIT PERIOD
5.8
Programming Time Segments
Some requirements for programming of the time seg-
ments:
Prop Seg + Phase Seg 1 >= Phase Seg 2
Prop Seg + Phase Seg 1 >= TDELAY
Phase Seg 2 > Sync Jump Width
For example, assuming that a 125 kHz CAN baud rate
with FOSC = 20 MHz is desired:
TOSC = 50 nsec, choose BRP<5:0> = 04h, then TQ =
500 nsec. To obtain 125 kHz, the bit time must be 16
TQ.
Typically, the sampling of the bit should take place at
about 60-70% of the bit time, depending on the system
parameters. Also, typically, the TDELAY is 1-2 TQ.
Sync Seg = 1 TQ; Prop Seg = 2 TQ; So setting Phase
Seg 1 = 7 TQ would place the sample at 10 TQ after the
transition. This would leave 6 TQ for Phase Seg 2.
Since Phase Seg 2 is 6, by the rules, SJW could be the
maximum of 4 TQ. However, normally a large SJW is
only necessary when the clock generation of the differ-
ent nodes is inaccurate or unstable, such as using
ceramic resonators. So an SJW of 1 is typically
enough.
5.9
Oscillator Tolerance
The bit timing requirements allow ceramic resonators
to be used in applications with transmission rates of up
to 125 kbit/sec, as a rule of thumb. For the full bus
speed range of the CAN protocol, a quartz oscillator is
required. A maximum node-to-node oscillator variation
of 1.7% is allowed.
Input Signal
Sync
Prop
Segment
Phase
Segment 1
Phase
Segment 2
≤ SJW
Sample
Actual
Nominal
Bit Length
TQ
Point
Bit Length
相关PDF资料 |
PDF描述 |
|---|---|
| MCP2140-I/SS | IC IRDA CONTROLLR DTE/DCE 20SSOP |
| PIC16LF726-I/SS | IC PIC MCU FLASH 8K 1.8V 28-SSOP |
| MCP2515-I/P | IC CAN CONTROLLER W/SPI 18DIP |
| PIC16F785-E/SS | IC PIC MCU FLASH 2KX14 20SSOP |
| PIC16F684-E/ST | IC PIC MCU FLASH 2KX14 14TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2510-ESO | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2510-EST | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2510-I/P | 功能描述:网络控制器与处理器 IC Stand-alone CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2510-I/P | 制造商:Microchip Technology Inc 功能描述:IC CAN CONTROLLER 2510 DIP18 |
| MCP2510-I/SO | 功能描述:网络控制器与处理器 IC Stand-alone CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。