- 您现在的位置：买卖IC网 > PDF目录11582 > MCP2515-E/P (Microchip Technology)IC CAN CONTROLLER W/SPI 18DIP PDF资料下载
参数资料
| 型号： | MCP2515-E/P |
| 厂商： | Microchip Technology |
| 文件页数： | 49/88页 |
| 文件大小： | 0K |
| 描述： | IC CAN CONTROLLER W/SPI 18DIP |
| 标准包装： | 25 |
| 控制器类型： | CAN 接口 |
| 接口： | SPI 串行 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 10mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 18-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 18-PDIP |
| 包装： | 管件 |
| 配用： | MCP2515DM-BM-ND - BOARD DEMO FOR MCP2515/51 MCP2515DM-PTPLS-ND - BOARD DAUGHTER PICTAIL MCP2515 MCP2515DM-PCTL-ND - BOARD DEMO FOR MCP2515 DV251001-ND - KIT DEVELOPMENT CAN MCP2510 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页
2010 Microchip Technology Inc.
DS21801F-page 53
MCP2515
8.0
OSCILLATOR
The MCP2515 is designed to be operated with a crystal
or ceramic resonator connected to the OSC1 and
OSC2 pins. The MCP2515 oscillator design requires
the use of a parallel cut crystal. Use of a series cut
crystal may give a frequency out of the crystal
manufacturer’s specifications. A typical oscillator circuit
is shown in Figure 8-1. The MCP2515 may also be
driven by an external clock source connected to the
OSC1 pin, as shown in Figure 8-2 and Figure 8-3.
8.1
Oscillator Startup Timer
The MCP2515 utilizes an Oscillator Startup Timer
(OST) that holds the MCP2515 in reset to ensure that
the oscillator has stabilized before the internal state
machine begins to operate. The OST maintains reset
for the first 128 OSC1 clock cycles after power-up or a
wake-up from Sleep mode occurs. It should be noted
that no SPI protocol operations should be attempted
until after the OST has expired.
8.2
CLKOUT Pin
The CLKOUT pin is provided to the system designer for
use as the main system clock or as a clock input for
other devices in the system. The CLKOUT has an inter-
nal prescaler which can divide FOSC by 1, 2, 4 and 8.
The CLKOUT function is enabled and the prescaler is
selected
via
the
CANCNTRL
register
(see
The CLKOUT pin will be active upon system reset and
default to the slowest speed (divide by 8) so that it can
be used as the MCU clock.
When Sleep mode is requested, the MCP2515 will
drive sixteen additional clock cycles on the CLKOUT
pin before entering Sleep mode. The idle state of the
CLKOUT pin in Sleep mode is low. When the CLKOUT
function is disabled (CANCNTRL.CLKEN = ‘0’) the
CLKOUT pin is in a high-impedance state.
The CLKOUT function is designed to ensure that
thCLKOUT and tlCLKOUT timings are preserved when the
CLKOUT pin function is enabled, disabled or the
prescaler value is changed.
FIGURE 8-1:
CRYSTAL/CERAMIC RESONATOR OPERATION
FIGURE 8-2:
EXTERNAL CLOCK SOURCE
Note:
The maximum frequency on CLKOUT is
specified as 25 MHz (See Table 13-5)
C1
C2
XTAL
OSC2
RS(1)
OSC1
RF(2)
SLEEP
To internal logic
Note 1: A series resistor (RS) may be required for AT strip cut crystals.
2: The feedback resistor (RF ), is typically in the range of 2 to 10 M
Ω.
Clock from
external system
OSC1
OSC2
Open
(1)
Note 1: A resistor to ground may be used to reduce system noise. This may increase system current.
2: Duty cycle restrictions must be observed (see Table 12-1).
相关PDF资料 |
PDF描述 |
|---|---|
| V150A15C400BL2 | CONVERTER MOD DC/DC 15V 400W |
| MCP2515T-E/SO | IC CAN CONTROLLER W/SPI 18SOIC |
| MCP2140T-I/SO | IC IRDA CONTROLLR DTE/DCE 18SOIC |
| VI-JNH-IW-F1 | CONVERTER MOD DC/DC 52V 100W |
| VI-JNF-IW-F1 | CONVERTER MOD DC/DC 72V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP2515-I | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2515-I/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Stand-Alone CAN Controller with SPI Interface |
| MCP2515-I/P | 功能描述:网络控制器与处理器 IC W/ SPI Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCP2515-I/P | 制造商:Microchip Technology Inc 功能描述:CAN controller IC |
| MCP2515-I/SO | 功能描述:网络控制器与处理器 IC W/ SPI Interface RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。