- 您现在的位置：买卖IC网 > PDF目录2097 > MCP3421A0T-E/OT (Microchip Technology)IC ADC 18BIT 3.75SPS 1CH SOT23-6 PDF资料下载
参数资料
| 型号： | MCP3421A0T-E/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 27/30页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 3.75SPS 1CH SOT23-6 |
| 标准包装： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 3.75 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 输入数目和类型： | 2 个单端，双极；1 个差分，单极 |
| 配用： | MCP3421EV-ND - BOARD EVAL FOR MCP3421 SOT23-6 |
| 其它名称： | MCP3421A0T-E/OTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页
MCP3421
DS22003B-page 6
2006 Microchip Technology Inc.
3.0
PIN DESCRIPTIONS
TABLE 3-1:
PIN FUNCTION TABLE
3.1
Analog Inputs (VIN+, VIN-)
VIN+ and VIN- are differential signal input pins. The
MCP3421 device accepts a fully differential analog
input signal which is connected on the VIN+ and VIN-
input pins. The differential voltage that is converted is
defined by VIN = (VIN+ - VIN-) where VIN+ is the voltage
applied at the VIN+ pin and VIN- is the voltage applied
at the VIN- pin. The input signal level is amplified by the
programmable gain amplifier (PGA) before the
conversion. The differential input voltage should not
exceed an absolute of (2* VREF/PGA) for accurate
measurement, where VREF is the internal reference
voltage (2.048V) and PGA is the PGA gain setting. The
converter output code will saturate if the input range
exceeds (2* VREF/PGA).
The absolute voltage range on each of the differential
input pins is from VSS-0.3V to VDD+0.3V. Any voltage
above or below this range will cause leakage currents
through the Electrostatic Discharge (ESD) diodes at
the input pins. This ESD current can cause unexpected
performance of the device. The common mode of the
analog inputs should be chosen such that both the
differential analog input range and the absolute voltage
range on each pin are within the specified operating
range
defined
in
3.2
Supply Voltage (VDD, VSS)
VDD is the power supply pin for the device. This pin
requires an appropriate bypass capacitor of about
0.1 F (ceramic) to ground. An additional 10 F
capacitor (tantalum) in parallel is also recommended
to further attenuate high frequency noise present in
some application boards. The supply voltage (VDD)
must be maintained in the 2.7V to 5.5V range for spec-
ified operation.
VSS is the ground pin and the current return path of the
device. The user must connect the VSS pin to a ground
plane through a low impedance connection. If an
analog ground path is available in the application PCB
(printed circuit board), it is highly recommended that
the VSS pin be tied to the analog ground path or
isolated within an analog ground plane of the circuit
board.
3.3
Serial Clock Pin (SCL)
SCL is the serial clock pin of the I2C interface. The
MCP3421 acts only as a slave and the SCL pin
accepts only external serial clocks. The input data
from the Master device is shifted into the SDA pin on
the rising edges of the SCL clock and output from the
MCP3421 occurs at the falling edges of the SCL clock.
The SCL pin is an open-drain N-channel driver.
Therefore, it needs a pull-up resistor from the VDD line
to the SCL pin. Refer to Section 5.3 “I2C Serial Com-
communication.
3.4
Serial Data Pin (SDA)
SDA is the serial data pin of the I2C interface. The SDA
pin is used for input and output data. In read mode, the
conversion result is read from the SDA pin (output). In
write mode, the device configuration bits are written
(input) though the SDA pin. The SDA pin is an open-
drain N-channel driver. Therefore, it needs a pull-up
resistor from the VDD line to the SDA pin. Except for
start and stop conditions, the data on the SDA pin must
be stable during the high period of the clock. The high
or low state of the SDA pin can only change when the
clock signal on the SCL pin is low. Refer to Section 5.3
Serial Interface communication.
Pin No
Sym
Function
1VIN+
Non-Inverting Analog Input Pin
2VSS
Ground Pin
3SCL
Serial Clock Input Pin of the I2C Interface
4SDA
Bidirectional Serial Data Pin of the I2C Interface
5VDD
Positive Supply Voltage Pin
6VIN-
Inverting Analog Input Pin
相关PDF资料 |
PDF描述 |
|---|---|
| MCP3424T-E/ST | IC ADC 18BIT 3.75SPS 4CH 14TSSOP |
| MCP3425A0T-E/CH | IC ADC 16BIT I2C PROGBL SOT23-6 |
| MCP3427-E/MF | IC ADC 16BIT I2C PROGBL 10-DFN |
| MCP3550T-60E/MS | IC ADC 22BIT 2.7V 1CH 8MSOP |
| MCP6541RT-I/OT | IC COMP 1.6V PUSH-PULL SOT23-5 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3421A1T-E/CH | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3421A1T-E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421A2T-E/CH | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3421A2T-E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421A3T-E/CH | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。