- 您现在的位置：买卖IC网 > PDF目录10735 > MCP3421A1T-E/CH (Microchip Technology)IC ADC 18BIT 3.75SPS 1CH SOT23-6 PDF资料下载
参数资料
| 型号： | MCP3421A1T-E/CH |
| 厂商： | Microchip Technology |
| 文件页数： | 15/42页 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 3.75SPS 1CH SOT23-6 |
| 产品培训模块： | MCP3901 Analog Front End |
| 标准包装： | 1 |
| 位数： | 18 |
| 采样率（每秒）： | 3.75 |
| 数据接口： | I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 输入数目和类型： | 2 个单端，双极；1 个差分，单极 |
| 产品目录页面： | 672 (CN2011-ZH PDF) |
| 其它名称： | MCP3421A1T-E/CHDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
MCP3421
DS22003E-page 22
2009 Microchip Technology Inc.
5.4
General Call
The device acknowledges the general call address
(0x00 in the first byte). The meaning of the general call
address is always specified in the second byte. Refer
to Figure 5-5. The device supports the following two
general calls.
For more information on the general call, or other I2C
modes, please refer to the Phillips I2C specification.
5.4.1
GENERAL CALL RESET
The general call reset occurs if the second byte is
‘00000110’ (06h). At the acknowledgement of this
byte, the device will abort current conversion and
perform an internal reset similar to a Power-On-Reset
(POR). All configuration and data register bits are reset
to default values.
5.4.2
GENERAL CALL CONVERSION
The general call conversion occurs if the second byte
is
‘00001000’ (08h). All devices on the bus initiate a
conversion simultaneously. When the device receives
this command, the configuration will be set to the One-
Shot Conversion mode and a single conversion will be
performed. The PGA and data rate settings are
unchanged with this general call.
FIGURE 5-5:
General Call Address
Format.
5.5
High-Speed (HS) Mode
The I2C specification requires that a high-speed mode
device must be ‘activated’ to operate in high-speed
mode. This is done by sending a special address byte
of “00001XXX” following the START bit. The “XXX” bits
are unique to the High-Speed (HS) mode Master. This
byte is referred to as the High-Speed (HS) Master
Mode Code (HSMMC). The MCP3421 device does not
acknowledge this byte. However, upon receiving this
code, the device switches on its HS mode filters and
communicates up to 3.4 MHz on SDA and SCL bus
lines. The device will switch out of the HS mode on the
next STOP condition.
For more information on the HS mode, or other I2C
modes, please refer to the Phillips I2C specification.
5.6
I2C Bus Characteristics
The I2C specification defines the following bus
protocol:
Data transfer may be initiated only when the bus
is not busy
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition
Accordingly, the following bus conditions have been
defined using Figure 5-6.
5.6.1
BUS NOT BUSY (A)
Both data and clock lines remain HIGH.
5.6.2
START DATA TRANSFER (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
5.6.3
STOP DATA TRANSFER (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations can be ended with a STOP condition.
5.6.4
DATA VALID (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition.
LSB
First Byte
ACK
X
0
0 A
A
XX X X XX X
(General Call Address)
Second Byte
Note:
The I2C specification does not allow
“00000000” (00h) in the second byte.
S
START
ACK
STOP
相关PDF资料 |
PDF描述 |
|---|---|
| MCP3421A3T-E/CH | IC ADC 18BIT 3.75SPS 1CH SOT23-6 |
| ADCMP581BCPZ-WP | IC COMPARATOR ECL UFAST 16-LFCSP |
| ADCMP582BCPZ-WP | IC COMPARATOR PECL UFAST 16LFCSP |
| ADCMP572BCPZ-WP | IC COMPARATOR CML 3.3-5V 16LFCSP |
| VE-J4V-MY-F4 | CONVERTER MOD DC/DC 5.8V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3421A2T-E/CH | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3421A2T-E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421A3T-E/CH | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3421A3T-E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit Analog-to-Digital Converter with I2C Interface and On-Board Reference |
| MCP3421A4T-E/CH | 制造商:Microchip Technology Inc 功能描述:ANALOG-TO-DIGITAL CONVERTER WITH 18-BIT 制造商:Microchip Technology Inc 功能描述:18-BIT DELTA-SIGMA ADC, SINGLE CHANNEL, 4SPS - Tape and Reel 制造商:Microchip Technology Inc 功能描述:IC ADC 18BIT I2C 4SPS SOT23-6 制造商:Microchip Technology Inc 功能描述:18-bit delta-sigma ADC, single channel, 4sps, 6 SOT-23 T/R |
发布紧急采购，3分钟左右您将得到回复。