- 您现在的位置：买卖IC网 > PDF目录16644 > MCP3421DM-WS (Microchip Technology)BOARD DEMO MCP3421 WEIGHT SCALE PDF资料下载
参数资料
| 型号： | MCP3421DM-WS |
| 厂商： | Microchip Technology |
| 文件页数： | 15/42页 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO MCP3421 WEIGHT SCALE |
| 标准包装： | 1 |
| 主要目的： | 参考设计，称量台 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MCP3421，MCP6V07，PIC18F4550 |
| 主要属性： | 2Kg测压元件，灵敏度为1 mV/V |
| 已供物品： | 板，线缆，CD，电源 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
MCP3421
DS22003E-page 22
2009 Microchip Technology Inc.
5.4
General Call
The device acknowledges the general call address
(0x00 in the first byte). The meaning of the general call
address is always specified in the second byte. Refer
to Figure 5-5. The device supports the following two
general calls.
For more information on the general call, or other I2C
modes, please refer to the Phillips I2C specification.
5.4.1
GENERAL CALL RESET
The general call reset occurs if the second byte is
‘00000110’ (06h). At the acknowledgement of this
byte, the device will abort current conversion and
perform an internal reset similar to a Power-On-Reset
(POR). All configuration and data register bits are reset
to default values.
5.4.2
GENERAL CALL CONVERSION
The general call conversion occurs if the second byte
is
‘00001000’ (08h). All devices on the bus initiate a
conversion simultaneously. When the device receives
this command, the configuration will be set to the One-
Shot Conversion mode and a single conversion will be
performed. The PGA and data rate settings are
unchanged with this general call.
FIGURE 5-5:
General Call Address
Format.
5.5
High-Speed (HS) Mode
The I2C specification requires that a high-speed mode
device must be ‘activated’ to operate in high-speed
mode. This is done by sending a special address byte
of “00001XXX” following the START bit. The “XXX” bits
are unique to the High-Speed (HS) mode Master. This
byte is referred to as the High-Speed (HS) Master
Mode Code (HSMMC). The MCP3421 device does not
acknowledge this byte. However, upon receiving this
code, the device switches on its HS mode filters and
communicates up to 3.4 MHz on SDA and SCL bus
lines. The device will switch out of the HS mode on the
next STOP condition.
For more information on the HS mode, or other I2C
modes, please refer to the Phillips I2C specification.
5.6
I2C Bus Characteristics
The I2C specification defines the following bus
protocol:
Data transfer may be initiated only when the bus
is not busy
During data transfer, the data line must remain
stable whenever the clock line is HIGH. Changes
in the data line while the clock line is HIGH will be
interpreted as a START or STOP condition
Accordingly, the following bus conditions have been
defined using Figure 5-6.
5.6.1
BUS NOT BUSY (A)
Both data and clock lines remain HIGH.
5.6.2
START DATA TRANSFER (B)
A HIGH to LOW transition of the SDA line while the
clock (SCL) is HIGH determines a START condition. All
commands must be preceded by a START condition.
5.6.3
STOP DATA TRANSFER (C)
A LOW to HIGH transition of the SDA line while the
clock (SCL) is HIGH determines a STOP condition. All
operations can be ended with a STOP condition.
5.6.4
DATA VALID (D)
The state of the data line represents valid data when,
after a START condition, the data line is stable for the
duration of the HIGH period of the clock signal.
The data on the line must be changed during the LOW
period of the clock signal. There is one clock pulse per
bit of data.
Each data transfer is initiated with a START condition
and terminated with a STOP condition.
LSB
First Byte
ACK
X
0
0 A
A
XX X X XX X
(General Call Address)
Second Byte
Note:
The I2C specification does not allow
“00000000” (00h) in the second byte.
S
START
ACK
STOP
相关PDF资料 |
PDF描述 |
|---|---|
| CB5023-000 | HEAT SHRINK TUBING |
| GCM22DSXS | CONN EDGECARD 44POS DIP .156 SLD |
| HRSR-400FR-10 | HEAT SHRINK TUBING |
| A1CXH-2436G | IDC CABLE - AKC24H/AE24G/X |
| CB5132-000 | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3421E64A0-E/SN | 功能描述:模数转换器 - ADC 18-B delta-sigma ADC Sngl Ch 64kb EEPROM RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3421EV | 功能描述:数据转换 IC 开发工具 MCP3421 SOT23-6 Eval Board RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| MCP3422 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
| MCP3422A0-E/MC | 功能描述:模数转换器 - ADC 18B delta-sigma ADC dual Ch 4sps RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3422A0-E/MF | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:18-Bit, Multi-Channel ???￡ Analog-to-Digital Converter with I2Ca?￠ Interface and On-Board Reference |
发布紧急采购，3分钟左右您将得到回复。