- 您现在的位置：买卖IC网 > PDF目录2012 > MCP3901A0T-E/SS (Microchip Technology)IC ENERGY METER AFE 2CH 20-SSOP PDF资料下载
参数资料
| 型号： | MCP3901A0T-E/SS |
| 厂商： | Microchip Technology |
| 文件页数： | 18/30页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER AFE 2CH 20-SSOP |
| 标准包装： | 1,600 |
| 位数： | 24 |
| 通道数： | 2 |
| 电压 - 电源，模拟： | 4.5 V ~ 5.5 V |
| 电压 - 电源，数字： | 2.7 V ~ 5.5 V |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
PCA2002
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 8 — 25 November 2011
25 of 30
NXP Semiconductors
PCA2002
32 kHz watch circuit with programmable output period and pulse width
14.3.2 Quality of solder joint
A flip-chip joint is considered to be a good joint when the entire solder land has been
wetted by the solder from the bump. The surface of the joint should be smooth and the
shape symmetrical. The soldered joints on a chip should be uniform. Voids in the bumps
after reflow can occur during the reflow process in bumps with high ratio of bump diameter
to bump height, i.e. low bumps with large diameter. No failures have been found to be
related to these voids. Solder joint inspection after reflow can be done with X-ray to
monitor defects such as bridging, open circuits and voids.
14.3.3 Rework
In general, rework is not recommended. By rework we mean the process of removing the
chip from the substrate and replacing it with a new chip. If a chip is removed from the
substrate, most solder balls of the chip will be damaged. In that case it is recommended
not to re-use the chip again.
Device removal can be done when the substrate is heated until it is certain that all solder
joints are molten. The chip can then be carefully removed from the substrate without
damaging the tracks and solder lands on the substrate. Removing the device must be
done using plastic tweezers, because metal tweezers can damage the silicon. The
surface of the substrate should be carefully cleaned and all solder and flux residues
and/or underfill removed. When a new chip is placed on the substrate, use the flux
process instead of solder on the solder lands. Apply flux on the bumps at the chip side as
well as on the solder pads on the substrate. Place and align the new chip while viewing
with a microscope. To reflow the solder, use the solder profile shown in application note
AN10365 “Surface mount reflow soldering description”.
14.3.4 Cleaning
Cleaning can be done after reflow soldering.
相关PDF资料 |
PDF描述 |
|---|---|
| MCP3903T-E/SS | IC AFE 24BIT 64KSPS 6CH 28SSOP |
| MCP3911A0T-E/ML | IC AFE 24BIT 125KSPS 2CH 20-QFN |
| MCP4725A3T-E/CH | IC DAC 12BIT EE W/I2C SOT23-6 |
| MCP4726A3T-E/CH | IC DAC 12BIT NV EEP I2C SOT-23-6 |
| MCP4728T-E/UN | IC DAC 12BIT W/I2C 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP3901A0T-I/ML | 功能描述:模数转换器 - ADC Dual CH Energy Meter Front End,SPI IF RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3901A0T-I/SS | 功能描述:模数转换器 - ADC Dual CH Energy Meter Front End,SPI IF RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| MCP3901A1-I/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A1-I/SS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Two Channel Analog Front End |
| MCP3901A1T-I/ML | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Two Channel Analog Front End |
发布紧急采购，3分钟左右您将得到回复。