- 您现在的位置：买卖IC网 > PDF目录9443 > MCP4013T-502E/CH (Microchip Technology)IC DGTL POT 5K 1CH SOT23-6 PDF资料下载
参数资料
| 型号： | MCP4013T-502E/CH |
| 厂商： | Microchip Technology |
| 文件页数： | 20/54页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 5K 1CH SOT23-6 |
| 标准包装： | 1 |
| 接片： | 64 |
| 电阻（欧姆）： | 5k |
| 电路数： | 1 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 易失 |
| 接口： | 2 线串行（芯片选择，增/减） |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 标准包装 |
| 产品目录页面： | 674 (CN2011-ZH PDF) |
| 其它名称： | MCP4013T-502E/CHDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页
2006 Microchip Technology Inc.
DS21978C-page 27
MCP4011/2/3/4
4.0
GENERAL OVERVIEW
The MCP4011/2/3/4 devices are general purpose
digital potentiometers intended to be used in
applications where a programmable resistance with
moderate bandwidth is desired.
Applications generally suited for the MCP4011/2/3/4
devices include:
Set point or offset trimming
Sensor calibration
Selectable gain and offset amplifier designs
Cost-sensitive mechanical trim pot replacement
The digital potentiometer is available in four nominal
resistances (RAB), where the nominal resistance is
defined as the resistance between terminal A and
terminal B. The four nominal resistances are 2.1 k
Ω,
5k
Ω, 10 kΩ and 50 kΩ.
There are 63 resistors in a string between terminal A
and terminal B. The wiper can be set to tap onto any of
these 63 resistors thus providing 64 possible settings
(including terminal A and terminal B).
Figure 4-1 shows a block diagram for the resistive
network of the device. Equation 4-1 shows the
calculation for the step resistance, while Equation 4-2
illustrates the calculation used to determine the
resistance between the wiper and terminal B.
FIGURE 4-1:
Resistor Block Diagram.
EQUATION 4-1:
RS CALCULATION
EQUATION 4-2:
RWB CALCULATION
1 LSb is the ideal resistance difference between two
successive codes. If we use N = 1 and RW = 0 in
Equation 4-2, we can calculate the step size for each
increment or decrement command.
The MCP4011 device offers a voltage divider
(potentiometer) with all terminals available on pins.
The MCP4012 is a true rheostat, with terminal A and
the wiper (W) of the variable resistor available on pins.
The MCP4013 device offers a voltage divider (potenti-
ometer) with terminal B connected to ground.
The MCP4014 device is a Rheostat device with
terminal A of the resistor floating, terminal B connected
to ground, and the wiper (W) available on pin.
The MCP4011 can be externally configured to
implement any of the MCP4012, MCP4013 or
MCP4014 configurations.
4.1
Serial Interface
A 2-wire synchronous serial protocol is used to
increment or decrement the digital potentiometer’s
wiper terminal. The Increment/Decrement (U/D)
protocol utilizes the CS and U/D input pins. Both inputs
are tolerant of signals up to 12.5V without damaging
the device. The CS pin can differenciate between two
high-voltage levels, VIH and VIHH. This enables
additional commands without requiring additional input
pins. The high-voltage commands (VIHH on the CS pin)
are similar to the standard commands and are
supported for compatability to the MCP401X family of
devices.
The simple U/D protocol uses the state of the U/D pin
at the falling edge of the CS pin to determine if
Increment or Decrement mode is desired. Subsequent
rising edges of the U/D pin move the wiper.
The wiper value will not underflow or overflow.
RS
A
RS
B
N = 63
N = 62
N = 61
N = 1
N = 0
RW (1)
W
01h
Analog
Mux
RW (1)
00h
RW (1)
3Dh
RW (1)
3Eh
RW (1)
3Fh
Note 1: The wiper resistance is tap dependent.
That is, each tap selection resistance
has a small variation. This variation
effects the smaller resistance devices
(2.1 k
Ω) more.
RS
RAB
63
---------
=
RWB
RABN
63
-------------- RW
+
=
N = 0 to 63 (decimal)
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6992MPS6-2#TRMPBF | IC OSC PWM VOLT CTLR TSOT23-6 |
| VE-B10-IU-F3 | CONVERTER MOD DC/DC 5V 200W |
| LTC6992MPS6-1#TRPBF | IC OSC PWM VOLT CTLR TSOT23-6 |
| VI-B5P-IU-F1 | CONVERTER MOD DC/DC 13.8V 200W |
| LTC6992MPS6-1#TRMPBF | IC OSC PWM VOLT CTLR TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4013T-503E/CH | 功能描述:数字电位计 IC 50k U/D single 6-bit V POT to GND RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP4013T-503E/MC | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013T-503E/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013T-503E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
| MCP4013T-503E/SN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Low-Cost 64-Step Volatile Digital POT |
发布紧急采购，3分钟左右您将得到回复。