参数资料
型号: MCP42XXEV
厂商: Microchip Technology
文件页数: 18/42页
文件大小: 0K
描述: BOARD EVALUATION MCP42XX
标准包装: 1
系列: PICkit™
主要目的: 数字电位器
嵌入式:
已用 IC / 零件: MCP4231,MCP4241,MCP4251,MCP4261
已供物品: 1 块组装板,1 块裸板,说明文档
MCP42XXEV Evaluation Board User’s Guide
2.4.2
The MCP4261 Device
To make variations to the commands sent to the MCP4261 device (from the commands
shown in the demo section), one must know the device memory map (see Table 2-3)
and the command formats (see Figure 2-3). For additional device operational
information, refer to the MCP4261 device data sheet (DS22059).
TABLE 2-3:
MEMORY MAP AND THE SUPPORTED COMMANDS
Address
00h
Function
Volatile Wiper 0
Memory
Type
RAM
Allowed Commands
Read, Write,
Disallowed
Commands (2)
Increment, Decrement
01h
Volatile Wiper 1
RAM Read, Write,
Increment, Decrement
02h
03h
Nonvolatile Wiper 0
Nonvolatile Wiper 1
EEPROM Read, Write (1)
EEPROM Read, Write (1)
Increment, Decrement
Increment, Decrement
04h
Volatile
TCON0 Register
RAM Read, Write Increment, Decrement
05h
STATUS Register
RAM
Read
Write, Increment,
Decrement
06h-0Fh Data EEPROM EEPROM Read, Write
Increment, Decrement
Note 1:
2:
8-bit Command
(Increment or Decrement)
When an EEPROM write is active, these are invalid commands and will generate
an error condition. The user should use a read of the STATUS register to determine
when the write cycle has completed. To exit the error condition, the user must take
the CS pin to the V IH level and then back to the active state (V IL or V IHH ).
This command on this address will generate an error condition. To exit the error
condition, the user must take the CS pin to the V IH level and then back to the active
state (V IL or V IHH ).
16-bit Command
(Read Data or Write Data)
Command Byte
Command Byte
Data Byte
A A A A C C D D
D D D D 1 0 9 8
3 2 1 0
A A A A C C D D D D D D D D D D
D D D D 1 0 9 8 7 6 5 4 3 2 1 0
3 2 1 0
Command
Bits
CC
1 0
Register Memory Data
Address Bits
Command
Bits
Register Memory
Address
Command
Bits
Data
Bits
0 0 = Write Data
0 1 = INCR
1 0 = DECR
1 1 = Read Data
FIGURE 2-3:
DS51898A-page 18
MCP42XX SPI Command Formats.
? 2010 Microchip Technology Inc.
相关PDF资料
PDF描述
MCP43XXEV BOARD EVALUATION MCP43XX
MCP46XXDM-PTPLS BOARD PICTAIL DIGI POT MCP4XXX
MCP46XXEV EVAL BOARD FOR MCP46XX
MCP4XXXDM-DB BOARD DAUGHTER DIGIPOT MCP4XXX
MCP6S2XEV BOARD EVALUATION FOR MCP6S2X
相关代理商/技术参数
参数描述
MCP431550R 制造商:Eaton Corporation 功能描述:TYPE MCP MOTOR CIRCUIT PROTECTOR 150A FOR SIZE 4 STARTER
MCP4331-103E/ML 功能描述:数字电位计 IC 10k SPI 7-bit Quad Chl, QFN20 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MCP4331-103E/ST 功能描述:数字电位计 IC 10k SPI 7-bit Quad Chl, TSSOP20 RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MCP4331-104E/ML 功能描述:数字电位计 IC 100k SPI 7-bit Quad Channel RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel
MCP4331-104E/ST 功能描述:数字电位计 IC 100k SPI 7-bit Quad Channel RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel