- 您现在的位置：买卖IC网 > PDF目录9317 > MCP4362T-104E/ST (Microchip Technology)IC DGTL POT QUAD 100K 14TSSOP PDF资料下载
参数资料
| 型号： | MCP4362T-104E/ST |
| 厂商： | Microchip Technology |
| 文件页数： | 25/59页 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT QUAD 100K 14TSSOP |
| 标准包装： | 2,500 |
| 系列： | WiperLock™ |
| 接片： | 257 |
| 电阻（欧姆）： | 100k |
| 电路数： | 4 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | 4 线 SPI（芯片选择） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
2009 Microchip Technology Inc.
DS22233A-page 31
MCP434X/436X
4.0
FUNCTIONAL OVERVIEW
This Data Sheet covers a family of four non-volatile
Digital Potentiometer and Rheostat devices that will be
referred to as MCP43XX. The MCP43X1 devices are
the Potentiometer configuration, while the MCP43X2
devices are the Rheostat configuration.
As the Device Block Diagram shows, there are four
main functional blocks. These are:
The POR/BOR operation and the Memory Map are
discussed in this section and the Resistor Network and
SPI operation are described in their own sections. The
Device Commands commands are discussed in
4.1
POR/BOR and RESET Operation
The Power-on Reset is the case where the device is
having power applied to it from VSS. The Brown-out
Reset occurs when a device had power applied to it,
and that power (voltage) drops below the specified
range.
The devices RAM retention voltage (VRAM) is lower
than the POR/BOR voltage trip point (VPOR/VBOR). The
maximum VPOR/VBOR voltage is less then 1.8V.
When VPOR/VBOR < VDD < 2.7V, the electrical
performance
may
not
meet
the
data
sheet
specifications. In this region, the device is capable of
reading and writing to its EEPROM and incrementing,
decrementing, reading and writing to its volatile
memory if the proper serial command is executed.
When VDD < VPOR/VBOR or the RESET pin is Low, the
pin weak pull-ups are enabled.
4.1.1
POWER-ON RESET
When the device powers up, the device VDD will cross
the VPOR/VBOR voltage. Once the VDD voltage crosses
the VPOR/VBOR voltage, the following happens:
Volatile wiper register is loaded with value in the
corresponding non-volatile wiper register
The TCON registers are loaded their default value
The device is capable of digital operation
4.1.2
BROWN-OUT RESET
When the device powers down, the device VDD will
cross the VPOR/VBOR voltage.
Once the VDD voltage decreases below the VPOR/VBOR
voltage the following happens:
Serial Interface is disabled
EEPROM Writes are disabled
If the VDD voltage decreases below the VRAM voltage,
the following happens:
Volatile wiper registers may become corrupted
TCON registers may become corrupted
As the voltage recovers above the VPOR/VBOR voltage
Serial commands not completed due to a brown-out
condition may cause the memory location (volatile and
non-volatile) to become corrupted.
4.1.3
RESET PIN
The RESET pin can be used to force the device into
the POR/BOR state of the device. When the RESET
pin is forced Low, the device is forced into the reset
state. This means that the TCON and STATUS
registers are forced to their default values and the
volatile wiper registers are loaded with the value in the
corresponding Non-Volatile wiper register. Also the
SPI interface is disabled. Any non-volatile write cycle
is not interrupted, and allowed to complete.
This feature allows a hardware method for all registers
to be updated at the same time.
4.1.4
INTERACTION OF RESET PIN AND BOR/
POR CIRCUITRY
Figure 4-1 shows how the RESET pin signal and the
POR/BOR signal interact to control the hardware reset
state of the device.
FIGURE 4-1:
POR/BOR Signal and
RESET Pin Interaction.
RESET (from pin)
POR/BOR signal
Device reset
相关PDF资料 |
PDF描述 |
|---|---|
| MS27497E16A35SC | CONN RCPT 55POS WALL MNT W/SCKT |
| MCP4362T-103E/ST | IC DGTL POT QUAD 10K 14TSSOP |
| MCP4361T-503E/ST | IC DGTL POT QUAD 50K 20TSSOP |
| GTC06A-24-79SX | CONN PLUG 5POS STRAIGHT W/SCKT |
| VI-BNW-MY-F2 | CONVERTER MOD DC/DC 5.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4362T-502E/ST | 功能描述:数字电位计 IC 5k SPI Qd Ch 8-Bit Nonvolatile memory RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP4362T-503E/ST | 功能描述:数字电位计 IC 50k SPI Qd Ch 8-Bit Nonvolatile memory RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP43XXEV | 功能描述:数字电位计开发工具 MCP43XX Eval Board RoHS:否 制造商:Arduino 产品:TinkerKit Rotary Potentiometers 工具用于评估:TinkerKit 电阻:4.7 kOhms 工作电源电压:0 V to 5 V |
| MCP4431-103E/ML | 功能描述:数字电位计 IC 10k I2Cquad Ch Pot 7bit volatile memory RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP4431-103E/ST | 功能描述:数字电位计 IC 10k I2Cquad Ch Pot 7bit volatile memory RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。