- 您现在的位置：买卖IC网 > PDF目录9327 > MCP4662T-503E/UN (Microchip Technology)IC POT DGTL 50K DUAL 10-MSOP PDF资料下载
参数资料
| 型号： | MCP4662T-503E/UN |
| 厂商： | Microchip Technology |
| 文件页数： | 39/92页 |
| 文件大小： | 0K |
| 描述： | IC POT DGTL 50K DUAL 10-MSOP |
| 标准包装： | 2,500 |
| 接片： | 257 |
| 电阻（欧姆）： | 50k |
| 电路数： | 2 |
| 温度系数： | 标准值 150 ppm/°C |
| 存储器类型： | 非易失 |
| 接口： | I²C（设备位址） |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
MCP454X/456X/464X/466X
DS22107A-page 44
2008 Microchip Technology Inc.
5.2
Wiper
Each tap point (between the RS resistors) is a
connection point for an analog switch. The opposite
side of the analog switch is connected to a common
signal which is connected to the Terminal W (Wiper)
pin.
A value in the volatile wiper register selects which
analog switch to close, connecting the W terminal to
the selected node of the resistor ladder.
The wiper can connect directly to Terminal B or to
Terminal A. A zero-scale connections, connects the
Terminal W (wiper) to Terminal B (wiper setting of
000h). A full-scale connections, connects the Terminal
W (wiper) to Terminal A (wiper setting of 100h or 80h).
In these configurations the only resistance between the
Terminal W and the other Terminal (A or B) is that of
the analog switches.
A wiper setting value greater than full-scale (wiper
setting of 100h for 8-bit device or 80h for 7-bit devices)
will also be a Full-Scale setting (Terminal W (wiper)
connected to Terminal A). Table 5-1 illustrates the full
wiper setting map.
Equation 5-2 illustrates the calculation used to deter-
mine the resistance between the wiper and terminal B.
EQUATION 5-2:
RWB CALCULATION
TABLE 5-1:
VOLATILE WIPER VALUE VS.
WIPER POSITION MAP
5.3
WiperLock Technology
The MCP4XXX device’s WiperLock technology allows
application-specific calibration settings to be secured in
the EEPROM without requiring the use of an additional
write-protect pin. There are two WiperLock Technology
configuration bits (WL0 and WL1). These bits prevent
the Non-Volatile and Volatile addresses and bits for the
specified resistor network from being written.
The
WiperLock
technology
prevents
the
serial
commands from doing the following:
Changing a volatile wiper value
Writing to a non-volatile wiper memory location
Changing the volatile TCON register value
For either Resistor Network 0 or Resistor Network 1
(Potx), the WLx bit controls the following:
Non-Volatile Wiper Register
Volatile Wiper Register
Volatile TCON register bits RxHW, RxA, RxW,
and RxB
High Voltage commands are required to enable and
disable WiperLock. Please refer to the Modify Write
command for operation.
5.3.1
POR/BOR OPERATION WHEN
WIPERLOCK TECHNOLOGY
ENABLED
The WiperLock Technology state is not affected by a
POR/BOR event. A POR/BOR event will load the
Volatile Wiper register value with the Non-Volatile
Wiper register value, refer to Section 4.1.
Wiper Setting
Properties
7-bit Pot 8-bit Pot
3FFh
081h
3FFh
101h
Reserved (Full-Scale (W = A)),
Increment and Decrement
commands ignored
080h
100h
Full-Scale (W = A),
Increment commands ignored
07Fh
041h
0FFh
081
W = N
040h
080h
W = N (Mid-Scale)
03Fh
001h
07Fh
001
W = N
000h
Zero Scale (W = B)
Decrement command ignored
R
WB
R
ABN
256
()
--------------R
W
+
=
N = 0 to 256 (decimal)
R
WB
R
ABN
128
()
--------------R
W
+
=
N = 0 to 128 (decimal)
8-bit Device
7-bit Device
相关PDF资料 |
PDF描述 |
|---|---|
| DS1306EN | IC RTC SERIAL ALARM IND 20-TSSOP |
| DS1306E | IC RTC SERIAL ALARM 20-TSSOP |
| DS1284 | IC TIMEKEEPER WATCHDOG 28-DIP |
| DS17887-5 | IC RTC 5V 8K NV RAM 24-EDIP |
| MCP4662T-104E/UN | IC POT DGTL 100K DUAL 10-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP46XXDM-PTPLS | 功能描述:数字电位计 IC MCP46XX PICtail Plus Daughter Board RoHS:否 制造商:Maxim Integrated 电阻:200 Ohms 温度系数:35 PPM / C 容差:25 % POT 数量:Dual 每 POT 分接头:256 弧刷存储器:Volatile 缓冲刷: 数字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作电源电压:1.7 V to 5.5 V 电源电流:27 uA 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:TQFN-16 封装:Reel |
| MCP46XXEV | 功能描述:数字电位计开发工具 MCP46XX Eval Board RoHS:否 制造商:Arduino 产品:TinkerKit Rotary Potentiometers 工具用于评估:TinkerKit 电阻:4.7 kOhms 工作电源电压:0 V to 5 V |
| MCP4706A0T-015E/CH | 制造商:Microchip Technology Inc 功能描述:IC, DAC, 16 bit, 3.4 MSPS, SOT-23-6; Resolution (Bits):8bit; Input Channel Type:Single Ended; Supply Voltage Range:2.7V to 5.5V; Digital IC Case Style:SOT-23; No. of Pins:6; Data Interface:I2C, Serial; Supply Current:210A |
| MCP4706A0T-E/CH | 功能描述:数模转换器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4706A0T-E/MAY | 功能描述:数模转换器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。