参数资料
型号: MCP4706A2T-E/MAY
厂商: Microchip Technology
文件页数: 68/86页
文件大小: 0K
描述: IC DAC 8BIT NV EEP I2C 6DFN
标准包装: 3,000
设置时间: 6µs
位数: 8
数据接口: EEPROM,I²C,串行
转换器数目: 1
电压电源: 单电源
功率耗散(最大): 1.1W
工作温度: -40°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 6-VDFN 裸露焊盘
供应商设备封装: 6-DFN(2x2)
包装: 带卷 (TR)
输出数目和类型: 1 电压,单极
采样率(每秒): *
MCP4706/4716/4726
DS22272C-page 70
2011-2012 Microchip Technology Inc.
8.9
Software I2C Interface Reset
Sequence
At times, it may become necessary to perform a
Software Reset Sequence to ensure the MCP47X6
device is in a correct and known I2C interface state.
This technique only resets the I2C state machine.
This is useful if the MCP47X6 device powers up in an
incorrect state (due to excessive bus noise, etc), or if
the master device is reset during communication.
Figure 8-9 shows the communication sequence to
software reset the device.
FIGURE 8-9:
Software Reset Sequence
Format.
The 1st Start bit will cause the device to reset from a
state in which it is expecting to receive data from the
master device. In this mode, the device is monitoring
the data bus in Receive mode and can detect if the
Start bit forces an internal Reset.
The nine bits of ‘1’ are used to force a Reset of those
devices that could not be reset by the previous Start bit.
This occurs only if the MCP47X6 is driving an A bit on
the I2C bus, or is in Output mode (from a Read
command) and is driving a data bit of ‘0’ onto the I2C
bus. In both of these cases, the previous Start bit could
not be generated due to the MCP47X6 holding the bus
low. By sending out nine ‘1’ bits, it is ensured that the
device will see an A bit (the master device does not
drive the I2C bus low to acknowledge the data sent by
the MCP47X6), which also forces the MCP47X6 to
reset.
The 2nd Start bit is sent to address the rare possibility
of an erroneous write. This could occur if the master
device was reset while sending a Write command to the
MCP47X6, AND then as the master device returns to
normal operation and issues a Start condition, while the
MCP47X6 is issuing an acknowledge. In this case, if
the 2nd Start bit is not sent (and the Stop bit was sent)
the MCP47X6 could initiate a write cycle.
The Stop bit terminates the current I2C bus activity. The
MCP47X6 waits to detect the next Start condition.
This sequence does not effect any other I2C devices
which may be on the bus, as they should disregard this
as an invalid command.
Note:
This technique is documented in AN1028.
S‘1’‘1’‘1’‘1’‘1’‘1’‘1’‘1’
S
P
Start
bit
Nine bits of ‘1’
Start bit
Stop bit
Note:
The potential for this erroneous write
ONLY occurs if the master device is reset
while sending a Write command to the
MCP47X6.
相关PDF资料
PDF描述
VE-B3N-MY-F3 CONVERTER MOD DC/DC 18.5V 50W
MCP4706A1T-E/MAY IC DAC 8BIT NV EEP I2C 6DFN
VE-B3M-MY-F1 CONVERTER MOD DC/DC 10V 50W
MS3108E36-8S CONN PLUG 47POS RT ANG W/SCKT
74LVX3245MTC IC TRANSCVR TRI-ST 8BIT 24TSSOP
相关代理商/技术参数
参数描述
MCP4706A3T-E/CH 功能描述:数模转换器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP4706A3T-E/MAY 功能描述:数模转换器- DAC Sngl 8B NV DAC w/Ext Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP471610M02041 制造商:Distributed By MCM 功能描述:Microsoft™ Xbox 360™ Replacement Black Game Controller 制造商:MCM 功能描述:MICROSOFT XBOX 360 CONTROLLER BLACK WIRED
MCP4716A0T-E/CH 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube
MCP4716A0T-E/MAY 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube