- 您现在的位置：买卖IC网 > PDF目录8856 > MCP4716A2T-E/CH (Microchip Technology)IC DAC 10BIT NV EEP I2C SOT-23-6 PDF资料下载
参数资料
| 型号： | MCP4716A2T-E/CH |
| 厂商： | Microchip Technology |
| 文件页数： | 3/86页 |
| 文件大小： | 0K |
| 描述： | IC DAC 10BIT NV EEP I2C SOT-23-6 |
| 标准包装： | 3,000 |
| 设置时间： | 6µs |
| 位数： | 10 |
| 数据接口： | EEPROM，I²C，串行 |
| 转换器数目： | 1 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 452mW |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-6 |
| 供应商设备封装： | SOT-23-6 |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 1 电压，单极 |
| 采样率（每秒）： | * |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页
2011-2012 Microchip Technology Inc.
DS22272C-page 11
MCP4706/4716/4726
106
THD:DAT Data input hold
time
100 kHz mode
0
—
ns
2.7V-5.5V, Note 6
400 kHz mode
0
—
ns
2.7V-5.5V, Note 6
1.7 MHz mode
0
—
ns
4.5V-5.5V, Note 6
3.4 MHz mode
0
—
ns
4.5V-5.5V, Note 6
107
TSU:DAT Data input setup
time
100 kHz mode
250
—
ns
400 kHz mode
100
—
ns
1.7 MHz mode
10
—
ns
3.4 MHz mode
10
—
ns
109
TAA
Output valid
from clock
100 kHz mode
—
3750
ns
400 kHz mode
—
1200
ns
1.7 MHz mode
—
150
ns
Cb = 100 pF,
—
310
ns
Cb = 400 pF,
3.4 MHz mode
—
150
ns
Cb = 100 pF,
110
TBUF
Bus free time
100 kHz mode
4700
—
ns
Time the bus must be free
before a new transmission
can start
400 kHz mode
1300
—
ns
1.7 MHz mode
N/A
—
ns
3.4 MHz mode
N/A
—
ns
TABLE 1-3:
I2C BUS DATA REQUIREMENTS (SLAVE MODE) (CONTINUED)
I2C AC Characteristics
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
-40
°C ≤ TA ≤ +125°C (Extended)
Operating Voltage VDD range is described in Electrical Characteristics
Param.
No.
Sym
Characteristic
Min
Max
Units
Conditions
Note 1:
As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(minimum 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
2:
A Fast mode (400 kHz) I2C bus device can be used in a Standard mode (100 kHz) I2C bus system, but
the requirement tSU;DAT ≥ 250 ns must then be met. This will automatically be the case if the device does
not stretch the Low period of the SCL signal. If such a device does stretch the Low period of the SCL
signal, it must output the next data bit to the SDA line.
TR max.+tSU;DAT = 1000 + 250 = 1250 ns (according to the Standard mode I
2C bus specification) before
the SCL line is released.
3:
The MCP47X6 device must provide a data hold time to bridge the undefined part between VIH and VIL of
the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested
in order to ensure that the output data will meet the setup and hold specifications for the receiving device.
4:
Use Cb in pF for the calculations.
5:
Not Tested. This parameter ensured by characterization.
6:
A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do
not unintentionally create a Start or Stop condition.
If this parameter is too short, it can create an unintentional Start or Stop condition to other devices on the
I2C bus line. If this parameter is too long, the Data Input Setup (TSU:DAT) or Clock Low time (TLOW) can be
affected.
Data Input: This parameter must be longer than tSP.
Data Output: This parameter is characterized, and tested indirectly by testing TAA parameter.
7:
Ensured by the TAA 3.4 MHz specification test.
8:
The specification is not part of the I
2
C specification. TAA = THD:DAT + TFSDA (or TRSDA).
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3Z-MY-F4 | CONVERTER MOD DC/DC 2V 20W |
| VE-B3Z-MX-F2 | CONVERTER MOD DC/DC 2V 30W |
| MCP4716A2T-E/MAY | IC DAC 10BIT NV EEP I2C 6DFN |
| VE-B3Z-MW-F1 | CONVERTER MOD DC/DC 2V 40W |
| MCP4716A1T-E/CH | IC DAC 10BIT NV EEP I2C SOT-23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP4716A3T-E/CH | 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4716A3T-E/MAY | 功能描述:数模转换器- DAC Sngl 10B NV DAC w/Ex Vref & I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4725A0T-E/CH | 功能描述:数模转换器- DAC Sngl 12B NV DAC RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| MCP4725A0T-E/CH-CUT TAPE | 制造商:Microchip 功能描述:MCP4725 Series 1 Ch I2C EEPROM Memory 5.5 V 12-Bit D/A Converter SMT - SOT-23-6 |
| MCP4725A1T-E/CH | 功能描述:数模转换器- DAC Sngl 12-B NV DAC w/ I2C interface RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。