参数资料
| 型号： | MCP6004-I/ST |
| 厂商： | Microchip Technology |
| 文件页数： | 5/42页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP QUAD 1.8V 14TSSOP |
| 标准包装： | 96 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 0.6 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 4500µV |
| 电流 - 电源： | 100µA |
| 电流 - 输出 / 通道： | 23mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 14-TSSOP |
| 包装： | 管件 |
| 产品目录页面： | 678 (CN2011-ZH PDF) |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
2009 Microchip Technology Inc.
DS21733J-page 13
MCP6001/1R/1U/2/4
4.0
APPLICATION INFORMATION
The MCP6001/2/4 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process and
is specifically designed for low-cost, low-power and
general-purpose applications. The low supply voltage,
low quiescent current and wide bandwidth makes the
MCP6001/2/4 ideal for battery-powered applications.
This device has high phase margin, which makes it
stable for larger capacitive load applications.
4.1
Rail-to-Rail Inputs
4.1.1
PHASE REVERSAL
The MCP6001/1R/1U/2/4 op amp is designed to
prevent phase reversal when the input pins exceed the
supply voltages. Figure 2-21 shows the input voltage
exceeding the supply voltage without any phase
reversal
.
4.1.2
INPUT VOLTAGE AND CURRENT
LIMITS
The ESD protection on the inputs can be depicted as
shown in Figure 4-1. This structure was chosen to
protect the input transistors, and to minimize input bias
current (IB). The input ESD diodes clamp the inputs
when they try to go more than one diode drop below
VSS. They also clamp any voltages that go too far
above VDD; their breakdown voltage is high enough to
allow normal operation, and low enough to bypass
quick ESD events within the specified limits.
FIGURE 4-1:
Simplified Analog Input ESD
Structures.
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
currents and voltages at the VIN+ and VIN– pins (see
Absolute Maximum Ratings at the beginning of
shows the recommended approach to protecting these
inputs. The internal ESD diodes prevent the input pins
(VIN+ and VIN–) from going too far below ground, and
the resistors R1 and R2 limit the possible current drawn
out of the input pins. Diodes D1 and D2 prevent the
input pins (VIN+ and VIN–) from going too far above
VDD, and dump any currents onto VDD. When
implemented as shown, resistors R1 and R2 also limit
the current through D1 and D2.
FIGURE 4-2:
Protecting the Analog
Inputs.
It is also possible to connect the diodes to the left of
resistors R1 and R2. In this case, current through the
diodes D1 and D2 needs to be limited by some other
mechanism. The resistors then serve as in-rush current
limiters; the DC current into the input pins (VIN+ and
VIN–) should be very small.
A significant amount of current can flow out of the
inputs when the common mode voltage (VCM) is below
high impedance may need to limit the usable voltage
range.
4.1.3
NORMAL OPERATION
The input stage of the MCP6001/1R/1U/2/4 op amps
use two differential CMOS input stages in parallel. One
operates at low common mode input voltage (VCM),
while the other operates at high VCM. WIth this
topology, the device operates with VCM up to 0.3V
above VDD and 0.3V below VSS.
The transition between the two input stages occurs
when VCM = VDD – 1.1V. For the best distortion and
gain linearity, with non-inverting gains, avoid this region
of operation.
4.2
Rail-to-Rail Output
The output voltage range of the MCP6001/2/4 op amps
is
VDD – 25 mV
(minimum)
and
VSS +25mV
(maximum) when RL =10kΩ is connected to VDD/2
information.
Bond
Pad
Bond
Pad
Bond
Pad
VDD
VIN+
VSS
Input
Stage
Bond
Pad
VIN–
V1
MCP600X
R1
VDD
D1
R1 >
VSS – (minimum expected V1)
2mA
R2 >
VSS – (minimum expected V2)
2mA
V2
R2
D2
R3
相关PDF资料 |
PDF描述 |
|---|---|
| MCP601RT-E/OT | IC OPAMP SNGL 2.7V SOT23-5 |
| MCP6023T-E/ST | IC OPAMP SNGL 2.5V 10MHZ 8TSSOP |
| MCP6031-E/MS | IC OPAMP SNGL 1.8V 8MSOP |
| MCP608T-I/ST | IC OPAMP 2.5V R-R W/CS 8TSSOP |
| MCP6232-E/SN | IC OPAMP 1.8V DUAL R-R 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP6004T-E/LT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp |
| MCP6004T-E/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp |
| MCP6004T-E/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp |
| MCP6004T-E/P | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:1 MHz, Low-Power Op Amp |
| MCP6004T-E/SL | 功能描述:运算放大器 - 运放 Quad 1.8V 1MHz RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。