参数资料
| 型号： | MCP601RT-E/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 5/34页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP SNGL 2.7V SOT23-5 |
| 标准包装： | 1 |
| 放大器类型： | 通用 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 2.3 V/µs |
| 增益带宽积： | 2.8MHz |
| 电流 - 输入偏压： | 1pA |
| 电压 - 输入偏移： | 700µV |
| 电流 - 电源： | 230µA |
| 电流 - 输出 / 通道： | 22mA |
| 电压 - 电源，单路/双路(±)： | 2.7 V ~ 6 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 678 (CN2011-ZH PDF) |
| 其它名称： | MCP601RT-E/OTDKR |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
2007 Microchip Technology Inc.
DS21314G-page 13
MCP601/1R/2/3/4
4.2
Rail-to-Rail Output
There are two specifications that describe the output
swing capability of the MCP601/1R/2/3/4 family of op
amps. The first specification (Maximum Output Voltage
Swing) defines the absolute maximum swing that can
be achieved under the specified load conditions. For
instance, the output voltage swings to within 15 mV of
the negative rail with a 25 k
Ω load to V
DD/2. Figure 2-33
shows how the output voltage is limited when the input
goes beyond the linear region of operation.
The second specification that describes the output
swing capability of these amplifiers is the Linear Output
Voltage Swing. This specification defines the maximum
output swing that can be achieved while the amplifier is
still operating in its linear region. To verify linear
operation in this range, the large signal (DC Open-Loop
Gain (AOL)) is measured at points 100 mV inside the
supply rails. The measurement must exceed the
specified gains in the specification table.
4.3
MCP603 Chip Select
The MCP603 is a single amplifier with Chip Select
(CS). When CS is pulled high, the supply current drops
to -0.7 A (typ.), which is pulled through the CS pin to
VSS. When this happens, the amplifier output is put into
a high-impedance state. Pulling CS low enables the
amplifier.
The CS pin has an internal 5 M
Ω (typical) pull-down
resistor connected to VSS, so it will go low if the CS pin
is left floating. Figure 1-1 is the Chip Select timing
diagram and shows the output voltage, supply currents,
and CS current in response to a CS pulse. Figure 2-27
shows the measured output voltage response to a CS
pulse.
4.4
Capacitive Loads
Driving large capacitive loads can cause stability
problems for voltage feedback op amps. As the load
capacitance increases, the feedback loop’s phase
margin decreases and the closed-loop bandwidth is
reduced. This produces gain peaking in the frequency
response with overshoot and ringing in the step
response.
When driving large capacitive loads with these op
amps (e.g., > 40 pF when G = +1), a small series
feedback loop’s phase margin (stability) by making the
output load resistive at higher frequencies. The
bandwidth will be generally lower than the bandwidth
with no capacitive load.
FIGURE 4-4:
Output resistor RISO
stabilizes large capacitive loads.
different capacitive loads and gains. The x-axis is the
normalized load capacitance (CL/GN) in order to make
it easier to interpret the plot for arbitrary gains. GN is the
circuit’s noise gain. For non-inverting gains, GN and the
gain are equal. For inverting gains, GN = 1 + |Gain|
(e.g., -1 V/V gives GN = +2 V/V).
FIGURE 4-5:
Recommended RISO values
for capacitive loads.
Once you have selected RISO for your circuit, double-
check the resulting frequency response peaking and
step response overshoot in your circuit. Evaluation on
the bench and simulations with the MCP601/1R/2/3/4
SPICE macro model are very helpful. Modify RISO’s
value until the response is reasonable.
4.5
Supply Bypass
With this family of op amps, the power supply pin (VDD
for single-supply) should have a local bypass capacitor
(i.e., 0.01 F to 0.1 F) within 2 mm for good high-
frequency performance. It also needs a bulk capacitor
(i.e., 1 F or larger) within 100 mm to provide large,
slow currents. This bulk capacitor can be shared with
nearby analog parts.
MCP60X
RISO
VOUT
CL
RF
RG
+
–
Normalized Load Capacitance;
CL / GN (F)
R
e
commended
R
IS
O
(
)
10p
100p
1n
10n
10
100
1k
GN = +1
GN ≥ +2
相关PDF资料 |
PDF描述 |
|---|---|
| MCP6023T-E/ST | IC OPAMP SNGL 2.5V 10MHZ 8TSSOP |
| MCP6031-E/MS | IC OPAMP SNGL 1.8V 8MSOP |
| MCP608T-I/ST | IC OPAMP 2.5V R-R W/CS 8TSSOP |
| MCP6232-E/SN | IC OPAMP 1.8V DUAL R-R 8SOIC |
| MCP629T-E/ML | IC OPAMP GP RR 20MHZ W/CS 16QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP601RT-EP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V to 6.0V Single Supply CMOS Op Amps |
| MCP601RT-ESL | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V to 6.0V Single Supply CMOS Op Amps |
| MCP601RT-ESN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V to 6.0V Single Supply CMOS Op Amps |
| MCP601RT-EST | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2.7V to 6.0V Single Supply CMOS Op Amps |
| MCP601RT-I/OT | 功能描述:运算放大器 - 运放 Single 2.7V RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。