- 您现在的位置：买卖IC网 > PDF目录3406 > MCP6N11T-002E/SN (Microchip Technology)IC AMP INSTR RRIO 1MHZ 8SOIC PDF资料下载
参数资料
| 型号： | MCP6N11T-002E/SN |
| 厂商： | Microchip Technology |
| 文件页数： | 24/50页 |
| 文件大小： | 0K |
| 描述： | IC AMP INSTR RRIO 1MHZ 8SOIC |
| 标准包装： | 3,300 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 输出类型： | 满摆幅 |
| 转换速率： | 9 V/µs |
| 增益带宽积： | 1MHz |
| 电流 - 输入偏压： | 10pA |
| 电压 - 输入偏移： | 2000µV |
| 电流 - 电源： | 800µA |
| 电流 - 输出 / 通道： | 30mA |
| 电压 - 电源，单路/双路(±)： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOICN |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
MCP6N11
DS25073A-page 30
2011 Microchip Technology Inc.
The input ESD diodes clamp the inputs when they try
to go more than one diode drop below VSS. They also
clamp any voltages that go too far above VDD; their
breakdown voltage is high enough to allow normal
operation, but not low enough to protect against slow
overvoltage (beyond VDD) events. Very fast ESD
events (that meet the spec) are limited so that damage
does not occur.
In some applications, it may be necessary to prevent
excessive voltages from reaching the op amp inputs.
Figure 4-5 shows one approach to protecting these
inputs. D1 and D2 may be small signal silicon diodes,
Schottky diodes for lower clamping voltages or diode-
connected FETs for low leakage.
FIGURE 4-5:
Protecting the Analog Inputs
Against High Voltages.
4.2.1.3
Input Current Limits
In order to prevent damage and/or improper operation
of these amplifiers, the circuit must limit the currents
into the input pins (see Section 1.1 “Absolute Maxi-
mum Ratings ”). This requirement is independent of
the voltage limits previously discussed.
Figure 4-6 shows one approach to protecting these
inputs. The resistors R1 and R2 limit the possible
current in or out of the input pins (and into D1 and D2).
The diode currents will dump onto VDD.
FIGURE 4-6:
Protecting the Analog Inputs
Against High Currents.
It is also possible to connect the diodes to the left of the
resistor R1 and R2. In this case, the currents through
the diodes D1 and D2 need to be limited by some other
mechanism. The resistors then serve as in-rush current
limiters; the DC current into the input pins (VIP and VIM)
should be very small.
A significant amount of current can flow out of the
inputs (through the ESD diodes) when the common
mode voltage (VCM) is below ground (VSS); see
4.2.1.4
Input Voltage Ranges
Figure 4-7 shows possible input voltage values
(VSS = 0V). Lines with a slope of +1 have constant VDM
(e.g., the VDM = 0 line). Lines with a slope of -1 have
constant VCM (e.g., the VCM =VDD/2 line).
For normal operation, VIP and VIM must be kept within
the region surrounded by the thick blue lines. The
horizontal and vertical blue lines show the limits on the
individual inputs. The blue lines with a slope of +1 show
the limits on VDM; the larger GMIN is, the closer they are
to the VDM = 0 line.
The input voltage range specs (VIVL and VIVH) change
with the supply voltages (VSS and VDD, respectively).
The differential input range specs (VDML and VDMH)
change with minimum gain (GMIN). Temperature also
affects these specs.
To take full advantage of VDML and VDMH, set VREF
(see Figure 1-6 and Figure 1-7) so that the output
(VOUT) is centered between the supplies (VSS and
VDD).
FIGURE 4-7:
Input Voltage Ranges.
VDD
V1
D1
V2
D2
U1
MCP6N11
min(R1,R2)>
VSS –min(V1,V2)
2mA
VDD
V1
R1
D1
V2
R2
D2
U1
MCP6N11
min(R1,R2) >
max(V1,V2)–VDD
2mA
VIP
VIM
V DM
=0
VIVH
VIVL
0
V
IV
H
V
IV
L
0
V D
M
=
V D
M
H
V
CM
=V
DD /2
V DM
=
V DM
H
VDD
V
DD
相关PDF资料 |
PDF描述 |
|---|---|
| P6KE400C-HF | TVS 600W 400V BIDIRECT DO-15 |
| TSM-108-01-L-DV-M | CONN HEADER 16POS .100" DBL SMD |
| MCP6N11T-001E/SN | IC AMP INSTR RRIO 500KHZ 8SOIC |
| PCN13-100S-2.54DSA | DIN CONN RCPT 100POS 2 ROW STR |
| 75844-802-72 | HDR STR DR .100 GP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP6N11T-005E/MNY | 功能描述:仪表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MCP6N11T-005E/SN | 功能描述:仪表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MCP6N11T-010E/MNY | 功能描述:仪表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MCP6N11T-010E/SN | 功能描述:仪表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
| MCP6N11T-100E/MNY | 功能描述:仪表放大器 Sngl Instrumentation Amp mCal E temp RoHS:否 制造商:Texas Instruments 通道数量: 输入补偿电压:150 V 可用增益调整: 最大输入电阻:10 kOhms 共模抑制比（最小值）:88 dB 工作电源电压:2.7 V to 36 V 电源电流:200 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:MSOP-8 封装:Bulk |
发布紧急采购，3分钟左右您将得到回复。