- 您现在的位置：买卖IC网 > PDF目录132985 > MCP79410-I/SN REAL TIME CLOCK, PDSO8 PDF资料下载
参数资料
| 型号： | MCP79410-I/SN |
| 元件分类： | 时钟/数据恢复及定时提取 |
| 英文描述： | REAL TIME CLOCK, PDSO8 |
| 封装： | 3.90 MM, ROHS COMPLIANT, PLASTIC, SOIC-8 |
| 文件页数： | 6/40页 |
| 文件大小： | 584K |
| 代理商： | MCP79410-I/SN |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
MCP7941X
DS22266C-page 14
2010-2011 Microchip Technology Inc.
4.2.3
CALIBRATION
The MCP7941X utilizes digital calibration to correct for
inaccuracies of the input clock source (either external
or crystal). These inaccuracies are due to crystal,
capacitor and temperature variations. Calibration is
enabled by modifying the value of the Calibration
register at address 08H. Calibration is achieved by
adding or subtracting a number of input clock cycles
per minute in order to achieve ppm level adjustments
in the internal timing function of the MCP7941X.
The MSB of the Calibration register is the sign bit, with
a ‘1’ indicating subtraction and a ‘0’ indicating addition.
The remaining seven bits in the register indicate the
number of input clock cycles (multiplied by two) that
are subtracted or added per minute to the internal
timing function.
The internal timing function can be monitored using
the MFP open-drain output pin by setting bit [6]
(SQWE) and bits [2:0] (RS2, RS1, RS0) of the control
register at address 07H. Note that the MFP output
waveform is disabled when the MCP7941X is running
in VBAT mode. With the SQWE bit set to ‘1’, there are
two methods that can be used to observe the internal
timing function of the MCP7941X:
A. RS2 BIT SET TO ‘0’
With the RS2 bit set to ‘0’, the RS1 and RS0 bits
enable the following internal timing signals to be
output on the MFP pin:
The frequencies listed in the table presume an input
clock source of exactly 32.768 kHz. In terms of the
equivalent number of input clock cycles, the table
becomes:
With regards to the calibration function, the Calibration
register setting has no impact upon the MFP output
clock signal when bits RS1 and RS0 are set to ‘11’.
The setting of the Calibration register to a non-zero
value (i.e., values other than 00H or 80H) enables the
calibration function which can be observed on the
MFP output pin. The calibration function can be
expressed in terms of the number of input clock cycles
added/subtracted from the internal timing function.
With bits RS1 and RS0 set to ‘00’, the calibration
function can be expressed as:
Since the calibration is done once per minute (i.e.,
when the internal minute counter is incremented), only
one cycle in sixty of the MFP output waveform is
affected by the calibration setting. Also note that the
duty cycle of the MFP output waveform will not
necessarily be at 50% when the calibration setting is
applied.
With bits RS1 and RS0 set to ‘01’ or ‘10’, the
calibration function can not be expressed in terms of
the input clock period. In the case where the MSB of
the Calibration register is set to ‘0’, the waveform
appearing at the MFP output pin will be “delayed”,
once per minute, by twice the number of input clock
cycles defined in the Calibration register. The MFP
waveform will appear as:
FIGURE 4-2:
RS1 AND RS0 WITH AND WITHOUT CALIBRATION
RS2
RS1
RS0
Output Signal
00
0
1 Hz
00
1
4.096 kHz
01
0
8.192 kHz
01
1
32.768 kHz
RS2
RS1
RS0
Output Signal
00
0
32768
00
1
8
01
0
4
01
1
Toutput = (32768 +/- (2 * CALREG)) Tinput
where:
Toutput = clock period of MFP output signal
Tinput = clock period of input signal
CALREG = decimal value of Calibration register
setting and the sign is determined
by the MSB of Calibration register.
Delay
Without calibration
With calibration
相关PDF资料 |
PDF描述 |
|---|---|
| MCP79410T-I/SN | REAL TIME CLOCK, PDSO8 |
| MPC603ERX250L | 32-BIT, 250 MHz, RISC PROCESSOR, CBGA255 |
| MPC603RRX240L | 32-BIT, 240 MHz, RISC PROCESSOR, CBGA255 |
| MPC603RRX250L | 32-BIT, 250 MHz, RISC PROCESSOR, CBGA255 |
| MK3233-01S | 50 MHz, OTHER CLOCK GENERATOR, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP79410T-I/MNY | 功能描述:实时时钟 I2C GP RTCC 1Kb EE 64B SRAM ID RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MCP79410T-I/MS | 功能描述:实时时钟 I2C GP RTCC 1Kb EE 64B SRAM ID RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MCP79410T-I/SN | 功能描述:实时时钟 I2C GP RTCC 1Kb EE 64B SRAM ID RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MCP79410T-I/ST | 功能描述:实时时钟 I2C GP RTCC 1Kb EE 64B SRAM ID RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 总线接口:I2C 日期格式:DW:DM:M:Y 时间格式:HH:MM:SS RTC 存储容量:64 B 电源电压-最大:5.5 V 电源电压-最小:1.8 V 最大工作温度:+ 85 C 最小工作温度: 安装风格:Through Hole 封装 / 箱体:PDIP-8 封装:Tube |
| MCP79411 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:I2C? Real-Time Clock/Calendar with EEPROM, SRAM, Unique ID and Battery Switchover |
发布紧急采购，3分钟左右您将得到回复。