- 您现在的位置：买卖IC网 > PDF目录17150 > MCP9800DM-TS1 (Microchip Technology)DEMO BOARD TEMP SENSOR MCP9800 PDF资料下载
参数资料
| 型号： | MCP9800DM-TS1 |
| 厂商： | Microchip Technology |
| 文件页数： | 27/42页 |
| 文件大小： | 0K |
| 描述： | DEMO BOARD TEMP SENSOR MCP9800 |
| 标准包装： | 1 |
| 传感器类型： | 温度 |
| 传感范围： | -55°C ~ 125°C |
| 接口： | I²C，SM 总线 |
| 灵敏度： | ±0.5°C |
| 电源电压： | 2.7 V ~ 5.5 V |
| 嵌入式： | 是，MCU，8 位 |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | MCP9800 |
| 产品目录页面： | 683 (CN2011-ZH PDF) |
| 相关产品： | MCP9800A0T-M/OTDKR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A5T-M/OTDKR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A5T-MOTGDKR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A0T-MOTGDKR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A5T-MOTGCT-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A0T-MOTGCT-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A5T-MOTGTR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A0T-MOTGTR-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A5T-M/OTCT-ND - IC SENSOR THERMAL 2.7V SOT23-5 MCP9800A0T-M/OTCT-ND - IC SENSOR THERMAL 2.7V SOT23-5 更多... |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
MCP9800/1/2/3
6.0
6.1
APPLICATIONS INFORMATION
Connecting to the Serial Bus
The ALERT output can be wired with a number of other
open-drain devices. In such applications, the output
needs to be programmed as an active-low output. Most
systems will require pull-up resistors for this
The SDA and SCL serial interface are open-drain pins
configuration.
that require pull-up resistors. This configuration is
6.3
Layout Considerations
The MCP9800/1/2/3 does not require any additional
components besides the master controller in order to
V DD
measure temperature. However, it is recommended
that a decoupling capacitor of 0.1 μF to 1 μF be used
PIC ?
MCU
R
R
MCP9800/1/2/3
SDA
SCL
between the V DD and GND pins. A high-frequency
ceramic capacitor is recommended. It is necessary for
the capacitor to be located as close as possible to the
power pins in order to provide effective noise
protection.
For applications where a switching regulator is used to
power the sensor, it is recommended to add a 200 ?
FIGURE 6-1:
Interface.
Pull-up Resistors on Serial
resistor in series to V DD to filter out the switcher noise
from the sensor. It is also recommended to add the
series resistor in applications where a linear regulator
The MCP9800/1/2/3 is designed to meet 0.4V
(maximum) voltage drop at 3 mA of current. This allows
the MCP9800/1/2/3 to drive lower values of pull-up
resistors and higher bus capacitance. In this
application, all devices on the bus must meet the same
pull-down current requirements.
is used to step-down a switching regulator voltage to
power the sensor. For example, if a linearly regulated
3.3V from a 5V switching regulator is used to power the
sensor, add a 200 ? series resistor (refer to Figure 6-3 ).
MCP9800/1/2/3
0.1 μF
6.2 Typical Application
Microchip provides several microcontroller product
lines with Master Synchronous Serial Port modules
(MSSP) that include the I 2 C interface mode. This
module implements all master and slave functions and
simplifies the firmware development overhead.
PIC16F737 as a master to control other Microchip
slave products, such as EEPROM, fan speed
Switching
Regulator
Switching
Regulator
200 ?
0.1 μF
bypass
200 ?
Linear
Regulator
bypass
V DD
MCP9800/1/2/3
V DD
controllers and the MCP9800 temperature sensor
connected to the bus.
FIGURE 6-3:
Single Resistor.
Power-supply Filter Using a
SDA SCL
6.4
Thermal Considerations
PIC16F737
Microcontroller
TC654
24LC01
EEPROM
The MCP9800/1/2/3 measures temperature by
monitoring the voltage of a diode located in the die. A
low-impedance thermal path between the die and the
Printed Circuit Board (PCB) is provided by the pins.
Therefore, the MCP9800/1/2/3 effectively monitors the
temperature of the PCB. However, the thermal path for
Fan Speed
Controller
FIGURE 6-2:
Bus.
TCN75A
Temperature
Sensor
Multiple Devices on I 2 C?
the ambient air is not as efficient because the plastic
device package functions as a thermal insulator.
A potential for self-heating errors can exist if the
MCP9800/1/2/3 SDA and SCL communication lines
are heavily loaded with pull-ups. Typically, the
self-heating error is negligible because of the relatively
small current consumption of the MCP9800/1/2/3.
However, in order to maximize the temperature
accuracy, the SDA and SCL pins need to be lightly
loaded.
? 2010 Microchip Technology Inc.
DS21909D-page 27
相关PDF资料 |
PDF描述 |
|---|---|
| RBM06DCMN | CONN EDGECARD 12POS .156 WW |
| 22R336MC | IND 33.0MH 37MA DRUM 7.8X7.5 SMD |
| HCM06DRYS | CONN EDGECARD 12POS DIP .156 SLD |
| 22R226MC | IND 22.0MH 44MA DRUM 7.8X7.5 SMD |
| GCM06DTBS | CONN EDGECARD 12POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP9800DM-TS1 | 制造商:Microchip Technology Inc 功能描述:TEMPERATURE SENSOR DEMO BOARD |
| MCP9801 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9801A0-M/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9801A0-M/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9801A0-M/SN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
发布紧急采购，3分钟左右您将得到回复。