- 您现在的位置：买卖IC网 > PDF目录19679 > MCP9802A5T-M/OT (Microchip Technology)IC TEMP SNSR 12BIT 2WIRE SOT23-5 PDF资料下载
参数资料
| 型号： | MCP9802A5T-M/OT |
| 厂商： | Microchip Technology |
| 文件页数： | 24/42页 |
| 文件大小： | 0K |
| 描述： | IC TEMP SNSR 12BIT 2WIRE SOT23-5 |
| 标准包装： | 1 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -55°C ~ 125°C |
| 精确度： | ±2°C（最小值） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 无 |
| 输出风扇： | 是 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 标准包装 |
| 产品目录页面： | 683 (CN2011-ZH PDF) |
| 其它名称： | MCP9802A5T-M/OTDKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
MCP9800/1/2/3
5.3.4.1
Shutdown Mode
5.3.4.3
ALERT Output Configuration
Operational Mode
The Shutdown mode disables all power-consuming
activities (including temperature sampling operations)
while leaving the serial interface active. The device
consumes 2 μA (maximum) in this mode. It remains in
this mode until the Configuration register is updated to
enable continuous conversion or until power is
recycled.
In Shutdown mode, the CONFIG, T A , T SET and T HYST
registers can be read or written to; however, the serial
bus activity will increase the shutdown current.
5.3.4.2 One-Shot Mode
The MCP9800/1/2/3 can also be used in a One-shot
mode that can be selected using bit 7 of the CONFIG
register. The One-shot mode performs a single
temperature measurement and returns to Shutdown
mode. This mode is especially useful for low-power
applications where temperature is measured upon
command from a controller. For example, a 9-bit T A in
One-shot mode consumes 200 μA (typical) for 30 ms
and 0.1 μA (typical) during shutdown.
To access this feature, the device needs to initially be
in Shutdown mode. This is done by sending a byte to
the CONFIG register with bit 0 set < 1 > and bit 7 cleared
< 0 >. Once the device is in Shutdown mode, the
CONFIG register needs to be written to again, with bit
0 and bit 7 set < 1 >. This begins the single conversion
cycle of t CONV , 30ms for 9-bit data. Once the
conversion is completed, T A is updated and bit 7 of
CONFIG becomes cleared < 0 > by the MCP9800/1/2/3.
TABLE 5-2: SHUTDOWN AND ONE-SHOT
MODE DESCRIPTION
One-Shot Shutdown
(Bit 7) (Bit 0)
The ALERT output can be configured as either a
comparator output or as Interrupt Output mode using
bit 1 of CONFIG. The polarity can also be specified as
an active-high or active-low using bit 2 of CONFIG. The
following sections describe each output mode, while
5.3.4.4 Comparator Mode
In Comparator mode, the ALERT output is asserted
when T A is greater than T SET . The pin remains active
until T A is lower than T HYST . The Comparator mode is
useful for thermostat-type applications, such as turning
on a cooling fan or triggering a system shutdown when
the temperature exceeds a safe operating range.
In Comparator mode, if the device enters the Shutdown
mode with asserted ALERT output, the output remains
active during shutdown. The device must be operating
in continuous conversion, with T A below T HYST , for the
ALERT output to be deasserted.
5.3.4.5 Interrupt Mode
In Interrupt mode, the ALERT output is asserted when
T A is greater than T SET . However, the output is
deasserted when the user performs a read from any
register. This mode is designed for interrupt-driven,
microcontroller-based systems. The microcontroller
receiving the interrupt will have to acknowledge the
interrupt by reading any register from the MCP9800/1/
2/3. This will clear the interrupt and the ALERT pin will
become deasserted. When T A drifts below T HYST , the
MCP9800/1/2/3 outputs another interrupt and the
controller needs to read a register to deassert the
ALERT output. Shutting down the device will also reset,
or deassert, the ALERT output.
Continuous Conversion
Shutdown
Continuous Conversion
(One-shot is ignored)
0 0
0 1
1 0
1 1
T SET
T A
T HYST
Note 1:
The shutdown command < 01 > needs to
be programmed before sending a
one-shot command < 11 >.
ALERT
Comparator mode
Active-low
ALERT
Interrupt mode
Active-low
Register
Read
*
DS21909D-page 24
FIGURE 5-7:
Alert Output.
? 2010 Microchip Technology Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| NCP1012APL100R2G | IC OFFLINE SW SMPS CM OVP 7DIPGW |
| PSA15R-075P | ADAPTER WALL R-SERIES 15W 7.5V |
| MIC5210-2.7BMM TR | IC REG LDO 2.7V .15A 8-MSOP |
| 171-050-203L021 | CONN DB50 FEMALE SLD CUP NICKEL |
| MIC5210-2.7BMM | IC REG LDO 2.7V .15A 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP9803 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9803A0-M/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9803A0-M/OT | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9803A0-M/SN | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
| MCP9803A0T-M/MS | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:2-Wire High-Accuracy Temperature Sensor |
发布紧急采购，3分钟左右您将得到回复。