- 您现在的位置：买卖IC网 > PDF目录19650 > MCP9808-E/MS (Microchip Technology)IC TEMP SENSOR DGTL I2C 8MSOP PDF资料下载
参数资料
| 型号： | MCP9808-E/MS |
| 厂商： | Microchip Technology |
| 文件页数： | 14/52页 |
| 文件大小： | 1085K |
| 描述： | IC TEMP SENSOR DGTL I2C 8MSOP |
| 标准包装： | 100 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部 |
| 感应温度： | -40°C ~ 125°C |
| 精确度： | ±1°C |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | 2 线串行，I²C?/SMBUS? |
| 输出警报： | 是 |
| 输出风扇： | 是 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-TSSOP，8-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 8-MSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
MCP9808
DS25095A-page 14
?2011 Microchip Technology Inc.
4.1.4
ADDRESS BYTE
Following the Start condition, the host must transmit an
8-bit address byte to the MCP9808. The address for the
MCP9808 temperature sensor is 0011,A2,A1,A0 in
binary, where the A2, A1 and A0 bits are set externally
by connecting the corresponding pins to V
DD
1 or GND
0. The 7-bit address, transmitted in the serial bit stream,
must match the selected address for the MCP9808 to
respond with an ACK. Bit 8 in the address byte is a
read/write bit. Setting this bit to 1 commands a read
operation, while 0 commands a write operation (see
Figure 4-1).
FIGURE 4-1:
Device Addressing.
4.1.5
DATA VALID
After the Start condition, each bit of data in the
transmission needs to be settled for a time specified by
t
SU-DATA
before SCL toggles from low-to-high (see the
Sensor Serial Interface Timing Specifications section).
4.1.6
ACKNOWLEDGE (ACK/NAK)
Each receiving device, when addressed, must
generate an ACK bit after the reception of each byte.
The master device must generate an extra clock pulse
for ACK to be recognized.
The Acknowledging device pulls down the SDA line for
t
SU-DATA
before the low-to-high transition of SCL from
the master. SDA also needs to remain pulled down for
t
H-DATA
after a high-to-low transition of SCL.
During read, the master must signal an End-of-Data
(EOD) to the slave, by not generating an ACK bit
(NAK), once the last bit has been clocked out of the
slave. In this case, the slave will leave the data line
released to enable the master to generate the Stop
condition.
4.1.7
TIME-OUT
If the SCL stays low or high for the time specified by
t
OUT
, the MCP9808 temperature sensor resets the
serial interface. This dictates the minimum clock speed
as outlined in the specification.
1 2 3 4 5 6 7 8 9
SCL
SDA
0 1 1 A2 A1 A0
Start
Address Byte
Slave
Address
R/W
MCP9808 Response
Code
Address
A
C
K
0
See Table 3-2.
相关PDF资料 |
PDF描述 |
|---|---|
| PQ05RD08 | IC REG LDO 5V .8A TO-220 |
| ATF1502ASV-20AI44 | IC CPLD 20NS 3.3V 44TQFP |
| ABC31DRES-S734 | CONN EDGECARD 62POS .100 EYELET |
| TAJT686M002RNJ | CAP TANT 68UF 2.5V 20% 1210 |
| HWS50-15/A | PWR SUP IND 15V 3.5A SNG OUTPUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCP9808T-E | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:?±0.5?°C Maximum Accuracy Digital Temperature Sensor |
| MCP9808T-E/MC | 功能描述:板上安装温度传感器 Silicon temp sensor with I2C interface RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| MCP9808T-E/MS | 功能描述:IC TEMP SENSOR DGTL I2C 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:3,000 系列:- 功能:温度开关 传感器类型:内部 感应温度:85°C 分界点 精确度:±6°C（最小值） 拓扑:ADC（三角积分型），比较器，寄存器库 输出类型:开路漏极 输出警报:是 输出风扇:是 电源电压:2.7 V ~ 5.5 V 工作温度:-55°C ~ 125°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:带卷 (TR) 其它名称:ADT6501SRJZP085RL7-ND |
| MCP98242 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
| MCP98242_09 | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Memory Module Temperature Sensor w/EEPROM for SPD |
发布紧急采购，3分钟左右您将得到回复。