- 您现在的位置：买卖IC网 > PDF目录16593 > MCZ33689DEWR2 (Freescale Semiconductor)IC SYSTEM BASIS CHIP LIN 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33689DEWR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 18/31页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS CHIP LIN 32-SOIC |
| 标准包装： | 1,000 |
| 应用： | 自动 |
| 电流 - 电源： | 5mA |
| 电源电压： | 5.5 V ~ 18 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 32-SOIC |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
33689
FUNCTIONAL DESCRIPTION
FUNCTIONAL DEVICE OPERATION
LIN-PU—LIN Pullup Enable Bit
This bit controls the LIN pullup resistor during Sleep and
Stop modes in accordance with Table 4. Reset clears the
LIN-PU bit.
HS3:HS1—High-Side H3:HS1 Enable Bits
These bits enable the HS3:HS1 bits in accordance with
Table 5. Reset clears the HSx bit.
Note If no PWM on HS1 and HS2 is required, the IN pin
must be connected to the VDD pin.
MODE2 and MODE1—Mode Section Bits
The MODE2 and MODE1 bits control the 33689 operating
modes in accordance with Table 6.
To safely enter Sleep or Stop mode and to ensure that
these modes are not affected by noise issue during SPI
transmission, the Sleep/Stop commands require two SPI
transmissions.
Sleep Mode Sequence The Sleep command, as shown in
Table 7, must be sent twice.
Stop Mode Sequence The Stop command, as shown in
Table 8, must be sent twice.
Table 4. LIN Pullup Termination Control Bit (D5)
LIN-PU
Description
0
30 k
Ω pullup connected in Sleep and Stop mode
1
30 k
Ω pullup disconnected in Sleep and Stop mode
Table 5. High-Side Switches Control Bits (D4, D3, and D2)
HS3
Description
HS2
Description
HS1
Description
0
HS3 OFF
0
HS2 OFF
0
HS1 OFF
1
HS3 ON
1
HS2 ON (if IN = 1)
1
HS1 ON (if IN = 1)
Table 6. Mode Control Bits (D1 and D0)
MODE2
MODE1
Description
0
Sleep mode (3)
0
1
Stop mode
1
0
Normal mode + Watchdog clear (4)
1
Normal mode
Notes
3.
Special SPI command and sequence is implemented in
order to avoid going into Sleep or Stop mode with a single
4.
When a logic [0] is written to MODE1 bit while MODE2 bit
is written as a logic [1]. After the SPI command is
completed, MODE1 bit is set to logic [1] and the 33689
stays in Normal mode. In order to set the 33689 in Sleep
mode, both MODE1 and MODE2 bits must be written in
the same 8-bit SPI command. The Watchdog clear on
Normal Request mode (150 ms) has no window.
Table 7. Sleep Command Bits
LINSL2
LINSL1
LIN-PU
HS3
HS2
HS1
MODE2
MODE1
11
x
0
x = Don’t care.
Table 8. Stop Command Bits
LINSL2 LINSL1
LIN-PU
HS3HS2
HS1
MODE2
MODE1
11
x
000
0
1
x = Don’t care.
相关PDF资料 |
PDF描述 |
|---|---|
| EEM28DRYH | CONN EDGECARD 56POS DIP .156 SLD |
| EVAL-ADCMP553BRMZ | BOARD EVALUATION ADCMP553BRMZ |
| ECM30DCAD | CONN EDGECARD 60POS R/A .156 SLD |
| 1025R-60K | COIL 47.UH MOLDED UNSHIELDED |
| VI-BN0-EW | CONVERTER MOD DC/DC 5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33730EK | 功能描述:线性稳压器 - 标准 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MCZ33730EK/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Switch Mode Power Supply with Multiple Linear Regulators |
| MCZ33730EKR2 | 功能描述:线性稳压器 - 标准 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| MCZ33742EG | 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33742EGR2 | 功能描述:网络控制器与处理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。