- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33884EG (Freescale Semiconductor)IC MULTIPLE CONTACT MON 24-SOIC PDF资料下载
参数资料
| 型号： | MCZ33884EG |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 6/21页 |
| 文件大小： | 0K |
| 描述： | IC MULTIPLE CONTACT MON 24-SOIC |
| 标准包装： | 30 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
33884
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
RUN COMMAND
The Run command gives access to all operating modes:
Normal, Polling, and Polling + INT Timer. It allows selection
of tWAIT and tWAKE, and configures the programmable input
blocks. Bit 7 is currently unused. Note that the Run register
values are unknown after exiting the Sleep mode.
MOD[2:1] OPERATING MODE
In the Run command, the two MOD bits place the device
in one of three operating modes: Normal, Polling, and Polling
+ INT Timer.
ST[3:1] – OFF TIME BETWEEN SAMPLES (TWAIT)
During both Polling modes (with and without INT Timer
wake up, MOD2=[1]), these bits select the interval of time
(tWAIT) the Input Blocks are turned OFF; switch transitions
are not detected during the OFF interval.
WT[2:1] – WAKE UP TIME
These bits allow the device to assert an external interrupt
(INT) at the following intervals during Polling mode (MOD2 =
MOD1 = 1).
Table 7. Run Command
MSB
LSB
Command
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Run
0
1
MOD2 MOD1
ST3
ST2
ST1
—
WT2
WT1
CP4
CP3
CP2
CP1
Reset Values:
Run Register
—
U
U = Unknown value coming out of Sleep mode. It must be configured with Run command.
Table 8. Bit Definition for Run Command
Command: Run (0001) with bits [12:1]
Mode
MOD2
MOD1
ST[3:1] WT[2:1] CP[4:1]
Undefined
0
xxx
xx
CP[4:1]
Normal
0
1
xxx
xx
CP[4:1]
Polling
1
0
ST[3:1]
xx
CP[4:1]
Polling + INT
Timer
1
ST[3:1] WT[2:1] CP[4:1]
Table 9. Sample OFF Time Prescales
ST[3:1]
Multiplier
Selected
OFF Time, tWAIT (ms)
[tDETECT (4.8ms typ) x
Multiplier]
ON Time
(ms)
000
5
15 - 25
5.1 - 6.3
001
9
30 - 55
5.1 - 6.3
010
17
60 - 90
5.1 - 6.3
011
25
100 - 140
5.1 - 6.3
100
33
145 - 185
5.1 - 6.3
101
41
195 - 215
5.1 - 6.3
110
49
220 - 245
5.1 - 6.3
111
57
250 - 320
5.1 - 6.3
Table 10. Wake Up Delay Prescales
WT[2:1]
Multiplier
Selected
Wake Up Interrupt, tWAIT (ms)
[tDETECT (2.8ms typ) x Multiplier]
00
512 + 1
2400 - 3200
01
256 + 1
1200 - 1600
10
128 + 1
600 - 750
11
64 + 1
290 - 360
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33905BD3EK | IC SBC CAN HS 3.3V 54SOIC |
| MCZ33972EWR2 | IC SWITCH DETECTION MULT 32-SOIC |
| MCZ33975AEKR2 | IC SWITCH DETECT MULT ENH 32SOIC |
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
| MCZ79076EGR2 | IC IGNITION CTRL ELECTR 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33884EG | 制造商:Freescale Semiconductor 功能描述:SWITCH MONITOR INTERFACE 24SOIC |
| MCZ33884EGR2 | 功能描述:多路器开关 IC SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 通道数量:1 开关数量:4 开启电阻（最大值）:7 Ohms 开启时间（最大值）: 关闭时间（最大值）: 传播延迟时间:0.25 ns 工作电源电压:2.3 V to 3.6 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UQFN-16 |
| MCZ33887EK | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33887EKR2 | 功能描述:马达/运动/点火控制器和驱动器 H-BRIDGE W/LD CUR FDBK RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| MCZ33887EKR2DH | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:5.0 A H-Bridge with Load Current Feedback |
发布紧急采购，3分钟左右您将得到回复。