- 您现在的位置：买卖IC网 > PDF目录11718 > MCZ33889BEG (Freescale Semiconductor)IC SYSTEM BASIS W/CAN 28-SOIC PDF资料下载
参数资料
| 型号： | MCZ33889BEG |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 22/59页 |
| 文件大小： | 0K |
| 描述： | IC SYSTEM BASIS W/CAN 28-SOIC |
| 标准包装： | 26 |
| 系列： | * |
| 应用： | * |
| 接口： | * |
| 电源电压： | * |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
33889
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
CYCLIC SENSE WAKE-UP (CYCLIC SENSE TIMER AND WAKE-UP INPUTS L0, L1)
The SBC can wake-up from a state change of one of the wake-up input lines (L0, L1), while the external pullup or pulldown
resistor of the switches associated to the wake-up input lines are biased with HS1 VSUP switch. The HS1 switch is activated in
sleep or stop mode from an internal timer. Cyclic sense and forced wake-up are exclusive. If Cyclic sense is enabled, the forced
wake-up can not be enabled.
INFO FOR CYCLIC SENSE + DUAL EDGE SELECTION
In case the Cyclic sense and Lx both level sensitive conditions are use together, the initial value for Lx inputs are sampled in
two cases:
1) When the register LPC[D3 and D0] are set and
2) At cyclic sense event, that is when device is in sleep or stop mode and HS1 is active.
The consequence is that when the device wake up by Lx transition, the new value is sampled as default, then when the device
is set back into low power again, it will automatically wake up.
The user should reset the LPC bits [D3 and D0] to 0 and set them again to the desired value prior to enter sleep or stop
mode.
FORCED WAKE-UP
The SBC can wake-up automatically after a predetermined time spent in sleep or stop mode. Forced wake-up is enabled by
setting bit FWU in the LPC register. Cyclic sense and forced wake-up are exclusive. If forced wake-up is enabled, the Cyclic
sense can not be enabled.
CAN WAKE-UP
The device can wake-up from a CAN message. A CAN wake-up cannot be disabled.
SPI WAKE-UP
The device can wake-up by the CS pin in sleep or stop mode. Wake-up is detected by the CS pin transition from a low to high
level. In stop mode this correspond to the condition where the MCU and SBC are both in Stop mode, and when the application
wake-up events come through the MCU.
SYSTEM POWER UP
At power up the device automatically wakes up.
DEVICE POWER UP, SBC WAKE UP
After device or system power up or a wake-up from sleep mode, the SBC enters into “reset mode” then into “normal request
mode”.
BATTERY FALL EARLY WARNING
This function provides an interrupt when the VSUP voltage is below the 6.1 V typical. This interrupt is maskable. A hysteresis
is included. Operation is only in Normal and Stand-by modes. VBAT low state reports in the IOR register.
RESET AND WDOG OPERATION
The following figure shows the reset and watchdog output operations. Reset is active at device power up and wake-up. Reset
is activated in case the VDD1 falls or the watchdog is not triggered. The WDOG output is active low as soon as the reset goes
low and stays low for as long as the watchdog is not properly re-activated by the SPI.
The WDOG output pin is a push pull structure than can drive external components of the application, for instance to signal the
MCU is in a wrong operation. Even if it is internally turned on (low-state), the reset pin can be forced to 5.0 V at 25 °C only, thanks
to its internally limited current drive capability. The WDOG stays low until the Watchdog register is properly addressed through
the SPI.
相关PDF资料 |
PDF描述 |
|---|---|
| V150A24E500BG | CONVERTER MOD DC/DC 24V 500W |
| MS27472T18B53S | CONN RCPT 53POS WALL MT W/SCKT |
| MCZ33889BEGR2 | IC SYSTEM BASIS W/CAN 28-SOIC |
| V150A24E500B2 | CONVERTER MOD DC/DC 24V 500W |
| D38999/24FE8SN | CONN RCPT 8POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33889BEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
| MCZ33889BEG/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:System Basis Chip with Low Speed Fault Tolerant CAN Interface |
| MCZ33889BEGR2 | 功能描述:网络控制器与处理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33889DEG | 功能描述:网络控制器与处理器 IC SBC-LITE-LS-CAN RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| MCZ33889DEG | 制造商:Freescale Semiconductor 功能描述:IC SYSTEM BASIS W/CAN TRANCEIVER |
发布紧急采购，3分钟左右您将得到回复。