- 您现在的位置：买卖IC网 > PDF目录1954 > MCZ33975AEKR2 (Freescale Semiconductor)IC SWITCH DETECT MULT ENH 32SOIC PDF资料下载
参数资料
| 型号： | MCZ33975AEKR2 |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 15/32页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH DETECT MULT ENH 32SOIC |
| 标准包装： | 1,000 |
| 应用： | 自动 |
| 接口： | SPI |
| 电源电压： | 5.5 V ~ 28 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 带卷 (TR) |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
22
Freescale Semiconductor
33975
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
The interrupt timer is used as a periodic wake-up timer. When
the timer expires, an interrupt is generated and the device
enters Normal mode.
Note: The interrupt timer in the 33975 device may be
disabled by programming the interrupt bits to logic [1 1 1].
Table 19 shows the programmable settings of the Interrupt
timer.
The scan timer sets the polling period between input switch
reads in Sleep mode. The period is set in the sleep command
and may be set to 000 (no period) to 111 (64 ms). In Sleep
mode when the scan timer expires, inputs will behave as
programmed prior to sleep command. The 33975 will wake
up for approximately 125
s and read the switch inputs. At
the end of the 125
s, the input switch states are compared
with the switch state prior to sleep command. When switch
state changes are detected, an interrupt (when enabled; refer
to wake-up/interrupt command description on page 17) is
generated and the device enters Normal mode. Without
switch state changes, the 33975 will reset the scan timer,
inputs become tri-state, and the Sleep mode continues until
the scan timer expires again.
Table 20 shows the programmable settings of the Scan
timer.
Note: The interrupt and scan timers are disabled in the
Normal Mode.
Figure 5, page 11, is a graphical description of how the
33975 device exits Sleep mode and enters Normal mode.
Notice that the device will exit Sleep mode when the interrupt
timer expires or when a switch change of state occurs. The
falling edge of INT triggers the MCU to wake from Sleep state.
Figure 12 illustrates the current consumed during Sleep
mode. During the 125
s, the device is fully active and switch
states are read. The quiescent current is calculated by
integrating the normal running current over scan period plus
approximately 60
A.
Figure 12. Sleep Current Waveform
TEMPERATURE MONITOR
With multiple switch inputs closed and the device
programmed with the wetting current timers disabled,
considerable power will be dissipated by the IC. For this
reason temperature monitoring has been implemented. The
temperature monitor is active in the Normal mode only. When
the IC temperature is above the thermal limit, the temperature
monitor will do all of the following:
Generate an interrupt.
Force all wetting current sources to revert to 2.0 mA/
4.0 mA sustain currents
Maintain the 2.0 mA/4.0 mA sustain currents and all
other functionality.
Set the thermal flag bit in the SPI output register.
The thermal flag bit in the SPI word will be cleared on the
rising edge of CS provided the die temperature has cooled
below the thermal limit. When die temperature has cooled
below thermal limit, the device will resume previously
programmed settings.
Table 19. Interrupt Timer
Bits 543
Interrupt Period
000
32 ms
001
64 ms
010
128 ms
011
256 ms
100
512 ms
101
1.024 s
110
2.048 s
111
No interrupt wake-up
Table 20. Scan Timer
Bits 210
Scan Period
000
No Scan
001
1.0 ms
010
2.0 ms
011
4.0 ms
100
8.0 ms
101
16 ms
110
32 ms
111
64 ms
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
Inputs active for 125 us
out of 32 ms
I=V/R or 0.270V/100ohm = 2.7mA
I=V/R or 6mV/100ohm = 60 uA
I=V/R or 0.270V/100
=2.7mA
Inputs active for
125
s out of 32ms
I=V/R or
6.0mV/100
=60A
相关PDF资料 |
PDF描述 |
|---|---|
| MCZ33993EWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
| MCZ79076EGR2 | IC IGNITION CTRL ELECTR 16-SOIC |
| MIC2070-2PCQS TR | IC USB PWR CTRLR DUAL 16-QSOP |
| MIC2550ABTS TR | IC USB TRANSCEIVER 14-TSSOP |
| MIC2550YTS | IC USB TRANSCEIVER 14-TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33975EK | 功能描述:接口 - 专用 MULTI SW DETECT RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MCZ33975EKR2 | 功能描述:接口 - 专用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MCZ33976EG | 功能描述:功率驱动器IC CONFIG DUAL GAUGE DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MCZ33976EG | 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GUAGE DRIVER SPI |
| MCZ33976EG/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Dual Gauge Driver with Configurable Response Time |
发布紧急采购，3分钟左右您将得到回复。