- 您现在的位置：买卖IC网 > PDF目录11715 > MCZ33975EK (Freescale Semiconductor)IC DETECTOR MULT SWITCH 32-SOIC PDF资料下载
参数资料
| 型号： | MCZ33975EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 18/32页 |
| 文件大小： | 0K |
| 描述： | IC DETECTOR MULT SWITCH 32-SOIC |
| 标准包装： | 42 |
| 应用： | 自动 |
| 接口： | SPI |
| 电源电压： | 5.5 V ~ 28 V |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOICW 裸露焊盘 |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
33975
TYPICAL APPLICATIONS
OPERATIONAL MODES
Figure 15. MOSFET or LED Driver Output
The sequence of commands (from Normal mode with inputs
tri-state) required to set up the device to drive a MOSFET are
as follows:
wetting current timer enable command –Disable SPn
metallic command –Set SPn to 16/32 mA or 2.0/4.0 mA
gate drive current (refer to Table 8, page 17).
settings command –Set SPn as switch-to-battery (refer
tri-state command –Disable tri-state for SPn (refer to
After the tri-state command has been sent (tri-state disable),
the MOSFET gate will be pulled to ground. From this point
forward the MOSFET may be turned on and off by sending
the settings command:
settings command –SPn as switch-to-ground
(MOSFET ON).
settings command –SPn as switch-to-battery
(MOSFET OFF).
Monitoring of the MOSFET drain in the OFF state provides
open load detection. This is done by using an input
comparator. With the SGn input in tri-state, the load will pull
up the input to battery. With the load open, the SGn pin is
pulled down to ground through an external resistor. The open
load is indicated by a logic [1] in the SO data bit.
The analog command may be used to monitor the drain
voltage in the MOSFET ON state. By sourcing 4.0 mA of
current to the 750
resistor, the analog voltage on the SGn
pin will be approximately:
As the voltage on the drain of the MOSFET increases, so
does the voltage on the SGn pin. With the SGn pin selected
as analog, the MCU may perform the A/D conversion.
Using this method for controlling unclamped inductive loads
is not recommended. Inductive fly-back voltages greater than
VPWR may damage the IC.
The SP0–SP7 pins of this device may also be used to send
signals from one module to another. Operation is similar to
the gate control of a MOSFET.
For LED applications a resistor in series with the LED is
recommended but not required. The switch-to-ground inputs
are recommended for LED application. To drive the LED use
the following commands:
wetting current timer enable command –Disable SGn
wetting current timer.
metallic command –Set SGn to 32 mA.
From this point forward the LED may be turned on and off
using the tri-state command:
tri-state command –Disable tri-state for SGn (LED ON).
tri-state command –Enable tri-state for SGn (LED
OFF).
These parameters are easily programmed via SPI
commands in Normal mode.
Multiple 33975 Devices in a Module System
Connecting power to the 33975 and the MCU for Sleep mode
operation may be done in several ways. Table 21 shows
several system configurations for power between the MCU
and the 33975 and their specific requirements for
functionality.
Multiple 33975 devices may be used in a module system. SPI
control may be done in parallel or serial. However when
parallel mode is used, each device is addressed
independently (refer to MCU Interface Description, page 15).
SP0
SG0
SG13
32
4.0
4.0 V Ref
+
-
Comparator
To SPI
VPWR
SG0
750
LO
A
D
VBAT
AMUX
100k
mA
VPWR
+
-
Comparator
To SPI
4.0 V
Ref
4.0
2.0 mA
16
mA
32
mA
VPWR
SG0
32
4.0
VPWR
mA
VPWR
+
Comparator
To SPI
4.0 V Ref
SG13
-
mA
Table 21. Sleep Mode Power Supply
MCU
VDD
33975
VDD
Comments
5.0V
All wake-up conditions apply. (Refer to Sleep
5.0V
0V
SPI wake-up is not possible.
0V
5.0V
Sleep mode is not possible. Current from the CS
pull-up will flow through the MCU to the VDD
that has been switched off. The negative edge
of CS will put 33975 in Normal mode.
0V
SPI wake-up is not possible.
VSGn = ISGn x 750 + VDS
相关PDF资料 |
PDF描述 |
|---|---|
| C8051T600-GS | IC 8051 MCU 8K OTP 14SOIC |
| VE-B10-IX-F3 | CONVERTER MOD DC/DC 5V 75W |
| MCZ33972AEWR2 | IC MULTIPLE SWITCH DETECT 32SOIC |
| MS27497T18A53S | CONN RCPT 53POS WALL MNT W/SCKT |
| VE-B10-IX-F1 | CONVERTER MOD DC/DC 5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33975EKR2 | 功能描述:接口 - 专用 MULTI SW DETECT INTERFACE RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| MCZ33976EG | 功能描述:功率驱动器IC CONFIG DUAL GAUGE DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| MCZ33976EG | 制造商:Freescale Semiconductor 功能描述:IC STEPPER MOTOR GUAGE DRIVER SPI |
| MCZ33976EG/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Dual Gauge Driver with Configurable Response Time |
| MCZ33976EGR2 | 功能描述:功率驱动器IC CONFIG DUAL GAUGE DR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。