- 您现在的位置：买卖IC网 > PDF目录17037 > MCZ33996EK (Freescale Semiconductor)IC SWITCH LOSIDE 16-OUTPT 32SOIC PDF资料下载
参数资料
| 型号： | MCZ33996EK |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH LOSIDE 16-OUTPT 32SOIC |
| 标准包装： | 42 |
| 类型： | 低端 |
| 输出数： | 16 |
| Rds（开）： | 550 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 1.2A |
| 输入电压： | 5 V ~ 27 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-BSOP（0.295"，7.50mm 宽）裸露焊盘 |
| 供应商设备封装： | 32-SOIC 裸露焊盘 |
| 包装： | 管件 |
LOGIC COMMANDS AND REGISTERS
INTRODUCTION
on output drain-to-source voltage (V DS ) > 2.7V. This feature
is designed to provide protection to loads that experience
more than expected currents and require fast shutdown. The
OR control to occur, the PWM Enable bit must be set to
logic [1].
33996 is designed to operate in both modes with full device
protection.
PWM ENABLE REGISTER
The PWM Enable register determines the outputs that are
PWM controlled. The first 8 bits of the 24 bit SPI message
On/Off Control Bit
PWM IN
AND/OR Control Bit
On/Off Control Bit
PWM Enable Bit
To Gate
Control
word are used to identify the PWM enable command, and the
remaining 16 bits are used to enable and disable the PWM of
the output drivers.
A logic [0] in the PWM Enable register will disable the
outputs as PWM. A logic [1] in the PWM Enable register will
set the specific output as a PWM. Power-ON Reset or the
RST pin or the RESET command will set the PWM Enable
register to logic [0].
AND/OR CONTROL REGISTER
The AND /OR Control register describes the condition by
which the PWM pin controls the output driver. A logic [0] in
the AND /OR Control register will AND the PWM input pin with
the ON /OFF Control register bit. Likewise, a logic [1] in the
AND /OR Control register will OR the PWM input pin with the
ON /OFF Control register bit (see Figure 12 ). For the AND /
On/Off control Bit
PWM IN
Figure 12. PWM Control Logic Diagram
SERIAL OUTPUT (SO) RESPONSE REGISTER
Fault reporting is accomplished through the SPI interface.
All logic [1s] received by the MCU via the SO pin indicate
fault. All logic [0s] received by the MCU via the SO pin
indicate no fault. All fault bits are cleared on the positive edge
of CS . SO bits 15 to 0 represent the fault status of outputs 15
to 0. SO bits 21 to 16 will always return logic [0]. Bit 22
provides over-voltage condition status and bit 23 is set when
any fault is present in the IC. The timing between two write
words must be greater than 450 μ s to allow adequate time to
sense and report the proper fault status.
RESET COMMAND
The RESET command turns all outputs OFF and sets the
following registers to a POR state (refer to Table 6 ).
? ON/OFF Control Register
? SFPD Control Register
? PWM Enable Register
? AND/OR Control Register
The Open Load Current Enable and the Global Shutdown
Registers are not affected by the RESET command.
33996
Analog Integrated Circuit Device Data
14
Freescale Semiconductor
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B7T-EY | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B7R-EY | CONVERTER MOD DC/DC 7.5V 50W |
| 0210491075 | CABLE JUMPER 1.25MM .030M 37POS |
| 0210491074 | CABLE JUMPER 1.25MM .030M 37POS |
| SDR0703-271KL | INDUCTOR POWER 270UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MCZ33996EK | 制造商:Freescale Semiconductor 功能描述:IC LOAD SWITCH 27V 32SOIC |
| MCZ33996EKR2 | 功能描述:开关变换器、稳压器与控制器 16 LOW SIDE SW 1.20HM RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCZ33998EG | 功能描述:开关变换器、稳压器与控制器 2.6/5.0V SWITCHING POWER RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| MCZ33998EG/R2 | 制造商:FREESCALE 制造商全称:Freescale Semiconductor, Inc 功能描述:Switching Power Supply with Linear Regulators |
| MCZ33998EGR2 | 功能描述:开关变换器、稳压器与控制器 2.6/5.0V SWITCHING POWER RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。