参数资料
| 型号： | MDF76-30P-1C |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | PLUG 30POS 1MM CRIMP |
| 标准包装： | 100 |
| 系列： | MDF76 |
| 连接器类型： | 插头 |
| 触点类型：： | 公母通用 |
| 位置数： | 30 |
| 间距： | 0.039"（1.00mm） |
| 行数： | 1 |
| 安装类型： | 自由悬挂 |
| 触点终端： | 压接 |
| 颜色： | 浅褐 |
| 包装： | 散装 |
| 请注意： | 不提供触点 |
| 配套产品： | H11696DKR-ND - CONN RCPT 30POS 1MM R/A GOLD SMD H11696CT-ND - CONN RCPT 30POS 1MM R/A GOLD SMD MDF76GW-30S-1H(55)-ND - CONN RCPT 30POS 1MM R/A SMD H11696TR-ND - CONN RCPT 30POS 1MM R/A GOLD SMD MDF76LBRW-30S-1H(55)-ND - CONN RCPT 30POS 1MM REV SMD MDF76TW-30S-1H(55)-ND - CONN RCPT 30POS 1MM R/A SMD MDF76URW-30S-1H(55)-ND - CONN RCPT 30POS 1MM LOPRO REV |
| 其它名称： | Q4161095 |
All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on MDF76 Series RoHS search at www.hirose-connectors.com, contact Interface Connectors
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
sales representative.
B Usage Recommendations
1.Recommended temperature profile
Temperature (?)
10sMAX
255?MAX
250
220?
200
30~60sec
180?
150
60~120sec
100
Time (Seconds)
Note 1: Up to 2 cycles of Reflow soldering is possible under the same
conditions, provided that there is a return to normal
temperature between the first and second cycle.
Note 2: The temperature profile indicates the board surface
temperature at the point of contacts with the connector
terminals.
2.Recommended manual soldering
3.Recommended screen thickness and open
area ratio
4.Board warpage
5.Cleaning conditions
6.Wire preparation and contact crimping
7.Crimped contact extraction
300±10? for 3 seconds
Thickness: 0.15 mm
Open area ratio: 100%
Maximum of 0.03 mm at the connector center, with both ends of the
connector as reference points.
Refer to "Nylon Connector Use Handbook".
Refer to “Nylon Connector Use Handbook”.
The crimp contact termination must be performed using specified tools.
All dimensions and crimp conditions are listed in applicable Crimp
Condition Table and Crimping Quality Standards Manual.
s Insert the contact retention tool in the insulator body and carefully lift the
molded-in retention tab while pulling on the wire at the same time (Fig. 1).
Do not deflect the molded-in retention tab more than is needed to release
the contact. The tab should return to its initial position after the contact is
removed.
Note: If the tab is not returning to it’s initial position carefully push I back
before inserting the crimped contact.
Permanent breakage of the molded-in retention tab will require
replacement of the entire plug.
Contact extraction tool
Plug
Molded-in contact retention tab
Pull-out
Contact
Figure 1. Contact Extraction
9
相关PDF资料 |
PDF描述 |
|---|---|
| MH10-14RX-BOTTLE | CONN RING HEATSHRINK #14 25PC |
| MH14-516R/SX-BOTTLE | CONN RING HEATSHRINK #5/16 25PC |
| MH18-8R/LX-BOTTLE | CONN RING HEATSHRINK #8 25PC |
| MINI-SACH-003G-P0.2 | CONN SOCKET 28-30AWG ACH CRIMP |
| MMS-102-01-T-DH | CONN RCPT 2MM 4POS DL HORZ PCB |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MDF76A-30P-1C | 制造商:Hirose 功能描述:547-0931-0-00 BAG 制造商:Hirose 功能描述:MDF76A-30P-1C |
| MDF76BKW-30S-1H(55) | 制造商:3M Electronic Products Division 功能描述: |
| MDF76GW-30P-1C | 制造商:HRS 制造商全称:HRS 功能描述:1.0 mm Pitch, Board-to-Wire LCD Interface Connectors |
| MDF76GW-30P-1H | 制造商:HRS 制造商全称:HRS 功能描述:1.0 mm Pitch, Board-to-Wire LCD Interface Connectors |
| MDF76GW-30S-1C | 制造商:HRS 制造商全称:HRS 功能描述:1.0 mm Pitch, Board-to-Wire LCD Interface Connectors |
发布紧急采购，3分钟左右您将得到回复。