- 您现在的位置：买卖IC网 > PDF目录384733 > MH89625C-5 (Mitel Networks Corporation) OPS/DID PCM SLIC Preliminary Information PDF资料下载
参数资料
| 型号： | MH89625C-5 |
| 厂商： | Mitel Networks Corporation |
| 英文描述： | OPS/DID PCM SLIC Preliminary Information |
| 中文描述： | 老年退休金计划/没有的PCM用户接口的初步信息 |
| 文件页数： | 4/16页 |
| 文件大小： | 150K |
| 代理商： | MH89625C-5 |
2-272
MH89625C
Preliminary Information
Functional Description
The Mitel MH89625C OPS SLIC (Off-Premise
Subscriber Line Interface Circuit) provides a
complete
interface
between
telephone line and an digital switching system. All
BORSCHT functions are provided requiring only a
few external components. The input impedance
conforms with Chinese standard requirements.
an
off-premise
All functions of the SLIC are controlled by the system
Drive (SD) outputs of the internal Mitel A-Law Codec
MT8967. The SD outputs are controlled by the serial
data input stream at CSTi.
The BORSCHT Functions
The MH89625C performs all of the BORSCHT
functions of Battery Feed, Overvoltage Protection,
Ringing, Supervision, Codec, Hybrid and Test.
Battery Feed
The MH89625C powers the telephone set with
constant DC loop current for short lines and
automatically reverts to constant voltage for long
lines. The constant loop current is a function of the
resistance connected from the LCA pin to V
EE.
Where I
Loop
is the desired constant loop current in mA,
and R is the resistance from pin LCA to pin V
EE
in
ohms.
Overvoltage Protection
The MH89625C is protected from short term (20ms)
transients (+250V) between TIP and RING, TIP and
ground, and RING and ground. However, additional
protection circuitry may be needed depending on the
requirements which must be met. Normally simple
external shunt protection as shown in Figure 4 is all
that is required.
R (k
)
open
348k
200k
80k
50k
30k
I
Loop
(mA)
22.0
25.0
27.1
34.0
40.2
49.7
147.2 -I
Loop
(0.0001176 X I
Loop
) -0.002586
R =
Ringing
The ringing insertion circuit has the capability to
provide ringing voltage to a telephone set by simply
adding an external relay, ring generator and a
transient protector. The internal relay driver switches
ringing voltage onto the line via the external ring
relay. A clamp diode is included which suppresses
voltage transients during relay switching caused by
the relay coil. The serial data input at CSTi controls
the internal Codec’s SDo output which activates the
ring driver. Refer to Table 1 for control of SLIC
functions.
Supervision
The loop detection circuit determines whether a low
enough resistance is across Tip and Ring to be
recognized as an off-hook condition. When an
off-hook condition occurs, the SHK and LED (the
LED output can drive an LED directly) outputs toggle
to a low level. These outputs also toggle with
incoming dial pulses.
During applied ringing (ring relay driver activated),
the loop detection circuit engages a ringing filter.
This filter prevents false off-hook detection due to
the current associated with the AC ringing voltage as
well as current transients that occur when the ringing
voltage is switched in and out. The ring trip detection
circuitry deactivates the ring relay driver after an
off-hook condition is detected.
Codec
The Codec function of the SLIC is implemented
using the Mitel MT8967 A-Law Codec. This device
provides the conversion interface between the
voiceband analog signals of a telephone subscriber
loop and the digital signals required in a digital PCM
(pulse code modulation) system. Eight-bit PCM
encoded digital data enters and leaves the chip
serially on DSTi and DSTo pins, respectively.
For detailed information on the CODEC portion of
the MH89625C, refer to the MT8967 integrated PCM
Filer/Codec data sheet (Microelectronics Digital
Communications Handbook, Mitel Semiconductor
Issue 9).
相关PDF资料 |
PDF描述 |
|---|---|
| MH89625C-6 | OPS/DID PCM SLIC Preliminary Information |
| MI402 | PIN DIODE RF POWER SWITCHING |
| MIC10937J-40 | DIODE ZENER SINGLE 200mW 11Vz 5mA-Izt 0.0545 0.1uA-Ir 8 SOD-323 3K/REEL |
| MIC10937 | V. F. Alphanumeric Display Controller |
| MIC10941 | V. F. Alphanumeric and Bargraph Display Controller Summary Information*?Not Recommended for New Designs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MH89625C-6 | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:OPS/DID PCM SLIC Preliminary Information |
| MH89626C | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:OPS/DID SLIC Preliminary Information |
| MH89626C-02 | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:OPS/DID SLIC Preliminary Information |
| MH89626C-04 | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:OPS/DID SLIC Preliminary Information |
| MH89726 | 制造商:MITEL 制造商全称:Mitel Networks Corporation 功能描述:MT8972 Loop Extender Circuits Advance Information |
发布紧急采购，3分钟左右您将得到回复。