- 您现在的位置：买卖IC网 > PDF目录19478 > MIC184YM TR (Micrel Inc)IC SUPERVISOR LOCAL/REMOTE 8SOIC PDF资料下载
参数资料
| 型号： | MIC184YM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 17/20页 |
| 文件大小： | 483K |
| 描述： | IC SUPERVISOR LOCAL/REMOTE 8SOIC |
| 标准包装： | 2,500 |
| 功能： | 温度监控系统（传感器） |
| 传感器类型： | 内部和外部 |
| 感应温度： | -55°C ~ 125°C，外部传感器 |
| 精确度： | ±2°C 本地（最大），±3°C 远程（最大） |
| 拓扑： | ADC（三角积分型），寄存器库 |
| 输出类型： | I²C?/SMBus? |
| 输出警报： | 是 |
| 输出风扇： | 无 |
| 电源电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -55°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC184YMTR MIC184YMTR-ND |
May 2006
17
MIC184
MIC184
Micrel
in most systems this will not be an issue.
Filter Capacitor Selection
When using a remote diode for temperature sensing, it is
sometimes desirable to use a lter capacitor between the
A2/T1 and GND pins of the MIC184. The use of this capaci-
tor is recommended in environments with a signicant high
frequency noise (such as digital switching noise), or if long
wires are used to connect to the remote diode. The maximum
recommended total capacitance from the A2/T1 pin to GND
is 2700pF. This usually suggests the use of a 2200pF NP0
or C0G ceramic capacitor with a 10% tolerance.
If the remote diode is to be at a distance of more than 6" ~
12" from the MIC184, using a shielded cable (solid foil shield
microphone cable is a good choice) for the connections to the
diode can signicantly help reduce noise pickup. Remember
to subtract the cable's conductor-to-shield capacitance from
the 2700pF maximum total capacitance.
Layout Considerations
Local Mode Only Applications:
If the MIC184 is not going to be used with an external diode,
the best layout is one which keeps it thermally coupled to the
subsystem(s) whose temperature it must monitor, while avoid-
ing any strong sources of EMI, RFI, or electrostatically coupled
noise. Two of the most common examples of such sources
are switching power supply transformers and CRTs.
Remote Mode Applications:
1. If the remote sensing capability of the
MIC184 will be used in an application, place the
MIC184 as close to the remote diode as pos-
sible, while taking care to avoid severe noise
sources (high frequency power transformers,
CRTs, memory and data busses, and the like).
2. Since any conductance from the various volt-
ages on the PC Board and the A2/T1 pin can
induce serious errors, it is good practice to guard
the remote diodes emitter trace with a pair of
ground traces. These ground traces should be
returned to the MIC184s own ground pin. They
should not be grounded at any other part of their
run. However, it is highly desirable to use these
guard traces to carry the diodes own ground
return back to the ground pin of the MIC184,
thereby providing a Kelvin connection for the
base of the diode. See Figure 8.
3. When using the MIC184 to sense the tempera-
ture of a processor or other device which has an
integral on-board diode (e.g., Intels Pentium
?/DIV>
III), connect the emitter and base of the remote
sensor to the MIC184 using the guard traces
and Kelvin return shown in Figure 8. The col-
lector of the remote diode is inaccessible to
the user on these types of chips. To allow for
this, the MIC184 has superb rejection of noise
appearing from collector to GND, as long as the
base to ground connection is relatively quiet.
4. Due to the small currents involved in the mea-
surement of the remote diodes 擵
BE
, it is
important to adequately clean the PC board after
soldering. This is most likely to show up as an
issue in some situations where water-soluble
soldering uxes are used.
5. In general, wider traces for the ground and
A2/T1 pins will help reduce susceptibility to radi-
ated noise (wider traces are less inductive). Use
trace widths and spacing of 10 mils wherever
possible. Wherever possible, place a ground
plane under the MIC184, and under the connec-
tions from the MIC184 to the remote diode. This
will help guard against stray noise pickup.
6. Always place a good quality V
DD
bypass ca-
pacitor directly adjacent to, or underneath, the
MIC184. This part should be a 0.1礔 ceramic
capacitor. Surface-mount parts provide the best
bypassing because of their low inductance.
7. When the MIC184 is being powered from par-
ticularly noisy power supplies, or from supplies
which may have sudden high-amplitude spikes
appearing on them, it can be helpful to add ad-
ditional power supply ltering. This should be
implemented as a 100?resistor in series with
the parts V
DD
pin, and a 4.7礔, 6.3V electrolytic
capacitor from V
DD
to GND. See Figure 9.
相关PDF资料 |
PDF描述 |
|---|---|
| 171-009-203L021 | CONN DB9 FEMALE SLD CUP NICKEL |
| V72A3V3E264BG3 | CONVERTER MOD DC/DC 3.3V 264W |
| T491D226M035AT | CAP TANT 22UF 35V 20% 2917 |
| 171-009-102L021 | CONN DB9 MALE SOLDER CUP TIN |
| V72A3V3E264BF2 | CONVERTER MOD DC/DC 3.3V 264W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC196 | 制造商:American DJ 功能描述:Laser Light Effect DMX Red Green and Blue Laser |
| MIC1R | 制造商:Velleman Inc 功能描述: |
| MIC1S | 制造商:Bogen Communications 功能描述:Module, Input;Screw;For amplifier, mic input, transformer balanced |
| MIC1X | 制造商:Bogen Communications 功能描述:Microphone Module M-Series 制造商:Bogen Communications 功能描述:AUDIO VISUAL INPUT MODULES; Leaded Process Compatible:No; Peak Reflow Compatible (260 C):No ;RoHS Compliant: No |
| MIC-2 | 功能描述:保险丝 250VAC 2A Fast Acting Indicating RoHS:否 制造商:Littelfuse 产品:Surface Mount Fuses 电流额定值:0.5 A 电压额定值:600 V 保险丝类型:Fast Acting 保险丝大小/组:Nano 尺寸:12.1 mm L x 4.5 mm W 安装风格: 端接类型:SMD/SMT 系列:485 |
发布紧急采购，3分钟左右您将得到回复。