- 您现在的位置：买卖IC网 > PDF目录16936 > MIC2003-0.8YM5 TR (Micrel Inc)IC DISTRIBUTION SW 0.8A SOT23-5 PDF资料下载
参数资料
| 型号： | MIC2003-0.8YM5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 27/30页 |
| 文件大小： | 0K |
| 描述： | IC DISTRIBUTION SW 0.8A SOT23-5 |
| 标准包装： | 3,000 |
| 类型： | 高端开关 |
| 输出数： | 1 |
| Rds（开）： | 100 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 800mA |
| 输入电压： | 2.5 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2003-0.8YM5TR MIC2003-0.8YM5TR-ND |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页
Micrel, Inc.
The VUVLO comparator uses no hysteresis. This is
because the VUVLO blanking timer prevents any
chattering that might otherwise occur if V IN varies about
the trigger point. The timer is reset by upward crossings
of the trip point such that V IN must remain below the trip
point for the full 32ms period for load disengagement to
occur.
In selecting a V TRIP voltage, the designer is cautioned to
not make this value less than 2.5V. A minimum of 2.5V
is required for the MIC20X6’s internal circuitry to
operate properly. VUVLO trip points below 2.5V will
result in erratic or unpredictable operation.
Kickstart?
MIC20xx Family
2003
2013
2004
2014
2005X
2015
2006
2016
2007
2017
2008
2018
2009X
2019X
Only parts in bold have Kickstart?.
(Not available in 5-pin SOT-23 packages).
Kickstart? allows brief current surges to pass to the
Figure 11. Kickstart?
Automatic Load Discharge
load before the onset of normal current limiting, which
permits dynamic loads to draw bursts of energy without
sacrificing system safety.
Functionally, Kickstart? is a forced override of the
2003 2004 2005X 2006 2007
2013 2014 2015 2016 2017
Only parts in bold have automatic load discharge.
2008
2018
2009X
2019X
normal current limiting function provided by the switch.
The Kickstart? period is governed by an internal timer
which allows current to pass up to the secondary
current limit (I LIMIT_2nd ) to the load for 128ms and then
normal (primary) current limiting goes into action.
During Kickstart?, a secondary current-limiting circuit
is monitoring output current to prevent damage to the
switch, as a hard short combined with a robust power
supply can result in currents of many tens of amperes.
This secondary current limit is nominally set at 4A and
reacts immediately and independently of the Kickstart?
period. Once the Kickstart? timer has finished its count
the primary current limiting circuit takes over and holds
I OUT to its programmed limit for as long as the excessive
load persists.
Once the switch drops out of current limiting the
Kickstart? timer initiates a lock-out period of 128ms
such that no further bursts of current above the primary
current limit, will be allowed until the lock-out period has
expired.
Kickstart? may be over-ridden by the thermal
protection circuit and if sufficient internal heating
occurs, Kickstart? will be terminated and I OUT 0A.
Upon cooling, if the load is still present I OUT I LIMIT , not
I LIMIT_2nd .
Automatic discharge is a valuable feature when it is
desirable to quickly remove charge from the V OUT pin.
This allows for a quicker power-down of the load. This
also prevents any charge from being presented to a
device being connected to the V OUT pin, for example,
USB, 1394, PCMCIA, and CableCARD?.
Automatic discharge is performed by a shunt MOSFET
from V OUT pin to GND. When the switch is disabled, a
break before make action is performed turning off the
main power MOSFET and then enabling the shunt
MOSFET. The total resistance of the MOSFET and
internal resistances is typically 126 ? .
Supply Filtering
A minimum 1 μ F bypass capacitor positioned close to
the V IN and GND pins of the switch is both good design
practice and required for proper operation of the switch.
This will control supply transients and ringing. Without a
bypass capacitor, large current surges or a short may
cause sufficient ringing on V IN (from supply lead
inductance) to cause erratic operation of the switch’s
control circuitry. For best-performance good quality,
low-ESR capacitors are recommended, preferably
ceramic.
When bypassing with capacitors of 10 μ F and up, it is
good practice to place a smaller value capacitor in
parallel with the larger to handle the high frequency
components of any line transients. Values in the range
of 0.01 μ F to 0.1 μ F are recommended. Again, good
quality, low-ESR capacitors should be chosen.
August 2011
27
M9999-080211-D
相关PDF资料 |
PDF描述 |
|---|---|
| 0210491100 | CABLE JUMPER 1.25MM .076M 39POS |
| MIC2026A-2YM TR | IC SW DISTRIBUTION 2CHAN 8SOIC |
| 0210490939 | CABLE JUMPER 1.25MM .254M 23POS |
| MIC2026A-1YM TR | IC SW DISTRIBUTION 2CHAN 8SOIC |
| SLP471M450H4P3 | CAP ALUM 470UF 450V 20% SNAP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2003-1.2YM5 | 功能描述:IC DISTRIBUTION SW 1.2A SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 电源分配开关 系列:- 特色产品:XRP252 Switches 标准包装:1 系列:- 类型:高端开关 输出数:2 Rds（开）:140 毫欧 内部开关:是 电流限制:1.15A 输入电压:1.75 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN（3x3） 包装:Digi-Reel® 其它名称:1016-1691-6 |
| MIC2003-1.2YM5 TR | 功能描述:电源开关 IC - USB Fixed Current Limit Single High-Side Switch - 1.2A - Lead Free RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MIC2003-1.2YM5TX | 功能描述:IC DISTRIBUTION SW 1.2A SOT23-5 RoHS:是 类别:集成电路 (IC) >> PMIC - 电源分配开关 系列:- 特色产品:XRP252 Switches 标准包装:1 系列:- 类型:高端开关 输出数:2 Rds（开）:140 毫欧 内部开关:是 电流限制:1.15A 输入电压:1.75 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN（3x3） 包装:Digi-Reel® 其它名称:1016-1691-6 |
| MIC2003-1.2YML | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Current Limiting Circuit Protector |
| MIC2003-1.2YML TR | 功能描述:电源开关 IC - USB Fixed Current Limit Single High-Side Switch - 1.2A - Lead Free RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。