- 您现在的位置：买卖IC网 > PDF目录11578 > MIC2010-2PZQS (Micrel Inc)IC USB PWR CTRLR DUAL 16-QSOP PDF资料下载
参数资料
| 型号： | MIC2010-2PZQS |
| 厂商： | Micrel Inc |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC USB PWR CTRLR DUAL 16-QSOP |
| 标准包装： | 98 |
| 控制器类型： | USB 电源控制器 |
| 接口： | USB |
| 电源电压： | 4.5 V ~ 5.5 V |
| 电流 - 电源： | 1mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 管件 |
January 2005
7
M9999-101104
MIC2010/2070
Micrel
Functional Description
The MIC2010/2070 are designed to support the power distri-
bution requirements for USB wakeup from the ACPI S3 state.
It integrates two independent channels under control of input
S3#. When S3# is asserted LOW (ACPI S3 state) the MIC2010/
2070 will switch a 500m MOSFET switch from the AUX
input to each of its two outputs. In addition the current-limit
threshold will be set to a value specified by a resistor
connected to the RSET inputs. Conversely when the S3#
input is HIGH the MIC2010/2070 will switch a 100m MOSFET
switch from the MAIN inputs to each of its two outputs. The
current-limit threshold is preset to 500mA in this state. The
lower current limit during the ACPI S3 state helps to ensure
that the standby supply maintains regulation even during fault
conditions.
Thermal Shutdown
Thermal shutdown is employed to protect the device from
damage should the die temperature exceed safe margins
due mainly to short circuit faults. Thermal shutdown shuts off
the output MOSFET and asserts the FAULT output if the die
temperature reaches 140°C and the overheated channel is in
current limit. The other channel is not affected. If however, the
die temperature exceeds 160°C, both channels will be shut
off even if neither channel is in current limit.
Power Dissipation
The device’s junction temperature depends on several fac-
tors such as the load, PCB layout, ambient temperature and
package type. The power dissipated in each channel is
P
D = RDS(on) × IOUT
2 where R
DS(on) is the on-resistance of the
internal MOSFETs and I
OUT is the continuous output current.
Total power dissipation of the device will be the summation of
P
D for both channels. To relate this to junction temperature,
the following equation can be used:
Functional Diagram
Current
Limit
10ms
Timer
Charge Pump
+
Gate Control
S3#
EN
Current
Limit
MAIN
OUT
AUX
RSET
/FAULT
AUX
Latch
To Other Channel
*
MAIN
FET
AUX
FET
*MIC2070-1/2 Only
Thermal
Sense
* 'P' options only
TJ = P
D × θJA + TA
where:
T
J = junction temperature
T
A = ambient temperature
θJA = is the thermal resistance of the package
Current Sensing and Limiting
The current-limit threshold of each channel is preset inter-
nally at 500mA when S3# is deasserted. When S3# is
asserted the current-limit threshold is specified by a resistor
connected to the RSET input. The value of the current-limit
threshold is determined by the equation 18/R
SET ohms where
R
SET is the resistance connected between the RSET pin and
ground. The current-limit threshold should be set at 1.2X of
the applications continous output current requirement.
When an overcurrent condition lasts longer than t
DLY the
MIC2070 will activate an internal circuit breaker that will latch
the output off and assert FAULT. The output will remain off
until either the load is removed or EN is toggled. When the
MIC2070 enters a latched output condition a 1mA pull-up
current source is activated. This provides a way to automati-
cally reset the output once the load is removed without the
need to toggle the enable input. Please refer to Figure 7 for
timing details.
The MIC2010 will automatically reset its output when the die
temperature cools down to 120°C. The MIC2010 output and
FAULT signal will continue to cycle on and off until the device
is disabled or the fault is removed. Figure 6 depicts typical
timing. Depending on PCB layout, package, ambient tem-
perature, etc., it may take several hundred milliseconds from
the incidence of the fault to the output MOSFET being shut
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16F1512-I/MV | IC MCU 8BIT 3.5KB FLASH 28-UQFN |
| 031-336 | BNC RIGHT ANGLE CRIMP RG-59 |
| 083-58SP | CONN UHF CONN BRAID CRIMP RG58 |
| 82-GB635-CR | TWIN AX PLUG INSULATED |
| MIC2010-2PZQS TR | IC USB PWR CTRLR DUAL 16-QSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2010-2PZQS TR | 功能描述:电源开关 IC - USB USB Power Controller - Lead Free RoHS:否 制造商:Micrel 电源电压-最小:2.7 V 电源电压-最大:5.5 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-8 封装:Tube |
| MIC2012 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:USB Power Controller Advance Information |
| MIC2012_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:USB Power Controller |
| MIC2012-1PBQS | 功能描述:IC USB PWR CTRLR DUAL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| MIC2012-1PBQS TR | 功能描述:IC USB PWR CTRLR DUAL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
发布紧急采购，3分钟左右您将得到回复。