参数资料
| 型号： | MIC2045-2YTS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 3/15页 |
| 文件大小： | 0K |
| 描述： | IC DISTRIBUTION SW SGL 16-TSSOP |
| 标准包装： | 2,500 |
| 类型： | 高端开关 |
| 输出数： | 1 |
| Rds（开）： | 30 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 可调 |
| 输入电压： | 0.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 16-TSSOP |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2045-2YTSTR MIC2045-2YTSTR-ND |
MIC2044/2045
Pin Description
Micrel
Pin Number
1
2
3
10
4
6
5
7,11,13,16
9,12,14
8
15
Pin Name
PWRGD
EN
/FAULT
GND
SLEW
ILIM
UVLOIN
VIN
VOUT
VBIAS
PGREF
Pin Function
Power-Good (Output): Open drain N-Channel device, active high. This pin
asserts high when the voltage at PGREF exceeds its threshold.
Switch Enable (Input): Gate control pin of the output MOSFET available as
an active high (–1) or active low (–2) input signal.
Fault Status (Output): Open drain N-Channel device, active low. This pin
indicates an overcurrent or thermal shutdown condition. For an overcurrent
event, /FAULT is asserted if the duration of the overcurrent condition lasts
longer than 32ms.
Ground connection: Tie to analog ground.
Slew-Rate Control (Input): A capacitor connected between this pin and
ground will reduce (slow) the output slew-rate. The output turn-on time must
be less than the nominal flag delay of 32ms in order to avoid nuisance
tripping of the /FAULT output since V OUT must be “fully on” (i.e., within
200mV of the voltage at the input) before the /FAULT signal delay elapses.
The slew-rate limiting capacitor requires a 16V rating or greater, 25V is
recommended. See “Applications Information: Output Slew-Rate Adjust-
ment” for further details.
Current Limit (Input): A resistor (R SET ) connected from this pin to ground
sets the current limit threshold as I LIMIT = CLF/R SET . CLF is the current limit
factor specified in the “Electrical Characteristics” table. For the MIC2044/45,
the continuous output current range is 1A to 6A.
Undervoltage Lockout Adjust (Input): With this pin left open, the UVLO
threshold is internally set to 1.45V. When the switching voltage (V IN ) is at or
below 1.5V, connecting an external resistive divider to this input will lower the
UVLO threshold. The total resistance of the divider must be less than 200k ? .
To disable the UVLO, tie this pin to VIN. See “Applications Information” for
further detail.
Switch Supply (Input): Connected to the drain of the output MOSFET. The
range of input for the switch is 0.8V to 5.5V. These pins must be externally
connected together to achieve rated performance.
Switch (Output): Connected to the source of the output MOSFET. These
pins must be externally connected together to achieve rated performance.
Bias Supply (Input): This input pin supplies power to operate the switch and
internal circuitry. The input range for VBIAS is 1.6V to 5.5V. When switched
voltage (V IN ) is between 1.6V to 5.5V and the use of a single supply is
desired, connect VBIAS to VIN externally.
Power-Good Threshold (Input): Analog reference used to specify the
PWRGD threshold. When the voltage at this pin exceeds its threshold, V TH ,
PWRGD is asserted high. An external resistive divider network is used to
determine the output voltage level at which V TH is exceeded. See the
“Functional Description” for further detail. When the PWRGD signal is not
utilized, this input should be tied to VOUT.
January 2005
3
MIC2044/2045
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2074-2YM TR | IC PWR DISTRIBUTION SW 2CH 8SOIC |
| MIC2076-2BN | IC DISTRIBUTION SW DUAL 8-DIP |
| MIC2077-2BWM TR | IC USB DISTRIB SW QUAD 16-SOIC |
| MIC2091-1YM5 TR | IC DISTRIBUTION SW 100MA SOT23-5 |
| MIC2097-2YMT TR | IC DISTRIBUTION SWITCH |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC207.5VP | 制造商:Littelfuse 功能描述:FUSE - MICRO2 BLADE 32V AG 7.5A 制造商:Littelfuse 功能描述:RETAIL / Fuse - Micro2 Blade 32V Ag 7.5A 5pc Card |
| MIC2070 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:USB Power Controller Advance Information |
| MIC2070-1BQS | 功能描述:IC USB PWR CTRLR DUAL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| MIC2070-1BQS TR | 功能描述:IC USB PWR CTRLR DUAL 16-QSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 控制器 系列:- 标准包装:2,450 系列:- 控制器类型:SPI 总线至 I²C 总线桥接 接口:I²C，串行，SPI 电源电压:2.4 V ~ 3.6 V 电流 - 电源:11mA 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-HVQFN（4x4） 包装:托盘 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名称:935286452157SC18IS600IBSSC18IS600IBS-ND |
| MIC2070-1CQS | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:USB Power Controller Advance Information |
发布紧急采购，3分钟左右您将得到回复。