- 您现在的位置：买卖IC网 > PDF目录16917 > MIC2077-2YWM TR (Micrel Inc)IC USB DISTRIB SW QUAD 16-SOIC PDF资料下载
参数资料
| 型号： | MIC2077-2YWM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 15/17页 |
| 文件大小： | 0K |
| 描述： | IC USB DISTRIB SW QUAD 16-SOIC |
| 标准包装： | 1,000 |
| 类型： | 高端开关 |
| 输出数： | 4 |
| Rds（开）： | 150 毫欧 |
| 内部开关： | 是 |
| 电流限制： | 900mA |
| 输入电压： | 2.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SOIC |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2077-2YWMTR MIC2077-2YWMTR-ND |
Micrel, Inc.
Application Information
Supply Filtering
A 0.1μF to 1μF bypass capacitor positioned close to V IN
and GND of the device is strongly recommended to
control supply transients. Without a bypass capacitor, an
output short may cause sufficient ringing on the input
(from supply lead inductance) to damage internal control
circuitry.
Printed Circuit Board Hot-Plug
The MIC2027/77 are ideal inrush current-limiters for hot-
plug applications. Due to the integrated charge pump,
the MIC2027/77 present a high impedance when off and
slowly becomes a low impedance as it turns on. This
“soft-start” feature effectively isolates power supplies
from highly capacitive loads by reducing inrush current.
In cases of extremely large capacitive loads (>400μF),
the length of the transient due to inrush current may
exceed the delay provided by the integrated filter. Since
this inrush current exceeds the current-limit flag delay
specification, FLG will be asserted during this time. To
MIC2027/2077
being asserted, an external RC filter, as shown in Figure
3, can be used to filter out transient FLG assertion. The
value of the RC time constant should be selected to
match the length of the transient, less t D(min) of the
MIC2027/77.
Universal Serial Bus (USB) Power Distribution
The MIC2027/77 is ideally suited for USB (Universal
Serial Bus) power distribution applications. The USB
specification defines power distribution for USB host
systems such as PCs and USB hubs. Hubs can either
be self-powered or bus-powered (that is, powered from
the bus). The requirement for USB self-powered hubs is
that the port must supply a minimum of 500mA at an
output voltage of 5V ±5%. In addition, the output power
delivered must be limited to below 25VA. Upon an
overcurrent condition, the host must also be notified. To
support hot-plug events, the hub must have a minimum
of 120μF of bulk capacitance, preferably low ESR
electrolytic or tantulum. Please refer to Application Note
17 for more details on designing compliant USB hub and
host systems.
prevent the logic controller from responding to FLG
Figure 3. Transient Filter
September 2006
15
M9999-091506
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2044-1BTS TR | IC DISTRIBUTION SW SGL 16-TSSOP |
| HCM11DRTH-S13 | CONN EDGECARD 22POS .156 EXTEND |
| 381LX221M400J452 | CAP ALUM 220UF 400V 20% SNAP |
| ECM18DTBH | CONN EDGECARD 36POS R/A .156 SLD |
| ISL21009BFB841Z-TK | IC VREF SERIES PREC 4.096V 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2085 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Single Channel Hot Swap Controllers |
| MIC2085JBQS | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC2085-JBQS | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2085-JYQS | 功能描述:热插拔功率分布 Single-channel Low Voltage Hot Swap Controller, VFAST = 100 mV, QSOP 16 (Lead-Free) RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| MIC2085-JYQS TR | 功能描述:热插拔功率分布 Single-channel Low Voltage Hot Swap Controller, VFAST = 100 mV, QSOP 16 (Lead-Free) RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。