- 您现在的位置：买卖IC网 > PDF目录19827 > MIC2085-JYQS TR (Micrel Inc)IC CTRLR HOT SWAP SGL 16-QSOP PDF资料下载
参数资料
| 型号： | MIC2085-JYQS TR |
| 厂商： | Micrel Inc |
| 文件页数： | 14/29页 |
| 文件大小： | 1008K |
| 描述： | IC CTRLR HOT SWAP SGL 16-QSOP |
| 产品培训模块： | Hot-Swap High-Voltage |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用型 Infiniband? |
| 内部开关： | 无 |
| 电源电压： | 2.3 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-QSOP |
| 包装： | 剪切带 (CT) |
| 其它名称： | 576-1492-1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
Micrel, Inc.
MIC2085/2086
May 2006
14
M9999-050406
(408) 955-1690
Functional Description
Hot Swap Insertion
When circuit boards are inserted into live system
backplanes and supply voltages, high inrush currents
can result due to the charging of bulk capacitance that
resides across the supply pins of the circuit board. This
inrush current, although transient in nature, may be high
enough to cause permanent damage to on-board
components or may cause the systems supply voltages
to go out of regulation during the transient period which
may result in system failures. The MIC2085/86 acts as a
controller for external N-Channel MOSFET devices in
which the gate drive is controlled to provide inrush
current limiting and output voltage slew rate control
during hot plug insertions.
Power Supply
VCC is the supply input to the MIC2085/86 controller
with a voltage range of 2.3V to 16.5V. The VCC input
can with stand transient spikes up to 33V. In order to
help suppress transients and ensure stability of the
supply voltage, a capacitor of 1.0礔 to 10礔 from VCC
to ground is recommended. Alternatively, a low pass
filter, shown in the typical application circuit, can be used
to eliminate high frequency oscillations as well as help
suppress transient spikes.
Start-Up Cycle
When the voltage on the ON pin rises above its
threshold of 1.24V, the MIC2085/86 first checks that its
supply (V
CC
) is above the UVLO threshold. If it does
check above, the device is enabled and an internal 2礎
current source begins charging capacitor C
POR
to 1.24V
to initiate a start-up sequence (i.e., start-up delay times
out). Once the start-up delay (t
START
) elapses, CPOR is
pulled immediately to ground and a 15礎 current source
begins charging the GATE output to drive the external
MOSFET that switches V
IN
to V
OUT
. The programmed
start-up delay is calculated using the following equation:
( )
礔
C
0.62
I
V
C
t
POR
CPOR
TH
POR
START
?/DIV>
E
?/DIV>
=
(1)
where V
TH
, the POR delay threshold, is 1.24V, and I
CPOR
,
the POR timer current, is 2礎. As the GATE voltage
continues ramping toward its final value (VCC + VGS) at
a defined slew rate (See Load Capacitance / Gate
Capacitance Dominated Start-Up sections), a second
CPOR timing cycle begins if:1)/FAULT is high and
2)CFILTER is low (i.e., not an overvoltage, undervoltage
lockout, or overcurrent state).This second timing cycle,
t
POR
, starts when the voltage at the FB pin exceeds its
threshold (V
FB
) indicating that the output voltage is valid.
The time period t
POR
is equivalent to t
START
and sets the
interval for the /POR to go Low-to-High after power is
good (See Figure 2 of Timing Diagrams ). Active
current regulation is employed to limit the inrush current
transient response during start-up by regulating the load
current at the programmed current limit value (See
Current Limiting and Dual-Level Circuit Breaker
section). The following equation is used to determine the
nominal current limit value:
SENSE
SENSE
TRIPSLOW
LIM
R
48mV
R
V
I
=
=
(2)
where V
TRIPSLOW
is the current limit slow trip threshold
found in the electrical table and R
SENSE
is the selected
value that will set the desired current limit. There are two
basic start-up modes for the MIC2085/86: 1)Start-up
dominated by load capacitance and 2)start-up
dominated by total gate capacitance. The magnitude of
the inrush current delivered to the load will determine the
dominant mode. If the inrush current is greater than the
programmed current limit (ILIM), then load capacitance
is dominant. Otherwise, gate capacitance is dominant.
The expected inrush current may be calculated using the
following equation:
GATE
LOAD
GATE
LOAD
GATE
C
C
15?/DIV>
C
C
I
INRUSH
?/DIV>
?/DIV>
E
?/DIV>
E
(3)
where I
GATE
is the GATE pin pull-up current, C
LOAD
is the
load capacitance, and C
GATE
is the total GATE
capacitance (CISS of the external MOSFET and any
external capacitor connected from the MIC2085/86
GATE pin to ground).
Load Capacitance Dominated Start-Up
In this case, the load capacitance, C
LOAD
, is large
enough to cause the inrush current to exceed the
programmed current limit but is less than the fast-trip
threshold (or the fast-trip threshold is disabled, M
option). During start-up under this condition, the load
current is regulated at the programmed current limit
value (ILIM) and held constant until the output voltage
rises to its final value. The output slew rate and
equivalent GATE voltage slew rate is computed by the
following equation:
LOAD
LIM
OUT
C
I
/dt
dV
Rate,
Slew
Voltage
Output
=
(4)
where I
LIM
is the programmed current limit value.
Consequently, the value of C
FILTER
must be selected to
ensure that the overcurrent response time, t
OCSLOW
,
exceeds the time needed for the output to reach its final
value. For example, given a MOSFET with an input
capacitance C
ISS
= C
GATE
=4700pF, C
LOAD
is 2200礔,
and I
LIMIT
is set to 6A with a 12Vinput, then the load
capacitance dominates as determined by the calculated
INRUSH > I
LIM
. Therefore, the output voltage slew rate
determined from Equation 4 is:
相关PDF资料 |
PDF描述 |
|---|---|
| XC2C256-7CPG132C | IC CR-II CPLD 256MCELL 132-BGA |
| RSO-1212S/H2 | CONV DC/DC 1W 9-18VIN 12VOUT |
| VI-BWW-CY-F4 | CONVERTER MOD DC/DC 5.5V 50W |
| RSO-1209S/H2 | CONV DC/DC 1W 9-18VIN 09VOUT |
| XC95144XL-5TQG144C | IC CPLD 3.2K 144MCELL 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2085-KBQS | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2085-KBQS TR | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2085-LBQS | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2085-LBQS TR | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| MIC2085-MBQS | 功能描述:IC CTRLR HOW SWAP SGL 16-QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。