- 您现在的位置：买卖IC网 > PDF目录15504 > MIC2168YMM (Micrel Inc)IC REG CTRLR BUCK PWM VM 10-MSOP PDF资料下载
参数资料
| 型号： | MIC2168YMM |
| 厂商： | Micrel Inc |
| 文件页数： | 9/14页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM VM 10-MSOP |
| 标准包装： | 100 |
| PWM 型： | 电压模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.1MHz |
| 占空比： | 90% |
| 电源电压： | 3 V ~ 14.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1092 (CN2011-ZH PDF) |
| 其它名称： | 576-1708-5 MIC2168YMM-ND |
V OUT × (V IN ( MAX ) ? V OUT )
R ESR ≤
1 ?
?
= I OUT ( MAX ) × 1 +
I INDUCTOR(RMS)
3 ? I OUT ( MAX ) ?
? I
?
(
)
PP × (1 ? D)
? + I PP × R ESR
? V OUT =
? C OUT × F S ?
= PP
I C
12
P DISS(C ) = I C × R ESR(C )
OUT(RMS) 2
MIC2168
I PP =
V IN ( MAX ) × F S × L
The peak inductor current is equal to the average output current
plus one half of the peak-to-peak inductor ripple current.
I PK = I OUT ( MAX ) + 0.5 × I PP
The RMS inductor current is used to calculate the I 2 × R
losses in the inductor.
2
I P
? ?
Maximizing ef?ciency requires the proper selection of core
material and minimizing the winding resistance. The high
frequency operation of the MIC2168 requires the use of fer-
rite materials for all but the most cost sensitive applications.
Lower cost iron powder cores may be used but the increase
in core loss will reduce the ef?ciency of the power supply.
This is especially noticeable at low output power. The winding
resistance decreases ef?ciency at the higher output current
levels. The winding resistance must be minimized although
this usually comes at the expense of a larger inductor. The
power dissipated in the inductor is equal to the sum of the
core and copper losses. At higher output loads, the core
losses are usually insigni?cant and can be ignored. At lower
output currents, the core losses can be a signi?cant con-
tributor. Core loss information is usually available from the
magnetics vendor. Copper loss in the inductor is calculated
by the equation below:
P INDUCTOR CU = I INDUCTOR(RMS) 2 × R WINDING
The resistance of the copper wire, R WINDING , increases with
temperature. The value of the winding resistance used should
be at the operating temperature.
R WINDING(HOT) = R WINDING(20 ° C) × ( 1 + 0.0042 × (T HOT ? T 20 ° C ) )
where:
T HOT = temperature of the wire under operating load
T 20°C = ambient temperature
R WINDING(20°C) is room temperature winding resistance (usu-
ally speci?ed by the manufacturer)
Output Capacitor Selection
The output capacitor values are usually determined capaci-
tors ESR (equivalent series resistance). Voltage and RMS
current capability are two other important factors selecting
the output capacitor. Recommended capacitors tantalum,
low-ESR aluminum electrolytics, and POSCAPS. The output
capacitor ’s ESR is usually the main cause of output ripple.
Micrel, Inc.
The output capacitor ESR also affects the overall voltage
feedback loop from stability point of view. See “Feedback Loop
Compensation” section for more information. The maximum
value of ESR is calculated:
? V OUT
I PP
where:
V OUT = peak-to-peak output voltage ripple
I PP = peak-to-peak inductor ripple current
The total output ripple is a combination of the ESR output
capacitance. The total ripple is calculated below:
2
2
?
where:
D = duty cycle
C OUT = output capacitance value
f S = switching frequency
The voltage rating of capacitor should be twice the voltage for
a tantalum and 20% greater for an aluminum electrolytic.
The output capacitor RMS current is calculated below:
I
OUT(RMS)
The power dissipated in the output capacitor is:
OUT OUT
Input Capacitor Selection
The input capacitor should be selected for ripple current rating
and voltage rating. Tantalum input capacitors may fail when
subjected to high inrush currents, caused by turning the input
supply on. Tantalum input capacitor voltage rating should
be at least 2 times the maximum input voltage to maximize
reliability. Aluminum electrolytic, OS-CON, and multilayer
polymer ?lm capacitors can handle the higher inrush currents
without voltage derating. The input voltage ripple will primarily
depend on the input capacitor ’s ESR. The peak input current
is equal to the peak inductor current, so:
? V IN = I INDUCTOR(PEAK) × R ESR(C IN )
The input capacitor must be rated for the input current ripple.
The RMS value of input capacitor current is determined at
the maximum output current. Assuming the peak-to-peak
inductor ripple current is low:
April 2005
9
M9999-040805
相关PDF资料 |
PDF描述 |
|---|---|
| MIC2169YMM | IC REG CTRLR BUCK PWM VM 10-MSOP |
| SP6136ER1-L | IC REG CTRLR BUCK PWM VM 16-QFN |
| LTC3822EDD#PBF | IC REG CTRLR BUCK PWM CM 10-DFN |
| SP6133ER1-L | IC REG CTRLR BUCK PWM VM 16-QFN |
| MIC3809YMM | IC REG CTRLR ISO PWM CM 8-MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2168YMM TR | 功能描述:直流/直流开关调节器 Replaced by MIC2168AYMM TR (Lead Free) RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2169 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169_09 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169A | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
| MIC2169A_09 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:500kHz PWM Synchronous Buck Control IC |
发布紧急采购，3分钟左右您将得到回复。