- 您现在的位置：买卖IC网 > PDF目录15370 > MIC2174C-1YMM TR (Micrel Inc)IC REG CTRLR BUCK PWM 10-MSOP PDF资料下载
参数资料
| 型号： | MIC2174C-1YMM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 12/27页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 10-MSOP |
| 标准包装： | 2,500 |
| 系列： | Hyper Speed Control™ |
| PWM 型： | 混合物 |
| 输出数： | 1 |
| 频率 - 最大： | 338kHz |
| 占空比： | 87% |
| 电源电压： | 3 V ~ 40 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
Micrel, Inc.
the FB voltage ripple, which occurs when V FB falls below
V REF , the OFF period ends and the next ON-time period
is triggered through the control logic circuitry.
Figure 2. MIC2174/MIC2174C Control Loop Timing
Figure 3 shows the load transient operation of the
MIC2174/MIC2174C converter. The output voltage drops
due to the sudden load increase, which causes the FB
voltage to be less than V REF . This will cause the error
comparator to trigger an ON-time period. At the end of
the ON-time period, a minimum OFF-time T OFF(min) is
generated to charge C BST since the FB voltage is still
below V REF . Then, the next ON-time period is triggered
due to the low FB voltage. Therefore, the switching
frequency changes during the load transient. With the
varying duty cycle and switching frequency, the output
recovery time is fast and the output voltage deviation is
small in MIC2174/MIC2174C converter.
Figure 3. MIC2174/MIC2174C Load-Transient Response
Unlike in current-mode control, the MIC2174/MIC2174C
uses the output voltage ripple, which is proportional to
the inductor current ripple if the ESR of the output
capacitor is large enough, to trigger an ON-time period.
The MIC2174/MIC2174C predetermined ON-time control
loop has the advantage of constant ON-time mode
MIC2174/MIC2174C
control that eliminates the need for the slope
compensation.
The MIC2174/MIC2174C has its own stability concern;
the FB voltage ripple should be in phase with the
inductor current ripple and large enough to be sensed by
the gm amplifier and the error comparator. The
recommended FB voltage ripple is 20mV~100mV. If a
low ESR output capacitor is selected, then the FB
voltage ripple may be too small to be sensed by the gm
amplifier and the error comparator. Also, the output
voltage ripple and the FB voltage ripple are not in phase
with the inductor current ripple if the ESR of the output
capacitor is very low. Therefore, the ripple injection is
required for a low ESR output capacitor. Please refer to
“Ripple Injection” subsection in “Application Information”
for more details about the ripple injection.
Soft-Start
Soft-start reduces the power supply input surge current
at startup by controlling the output voltage rise time. The
input surge appears while the output capacitor is
charged up. A slower output rise time will draw a lower
input surge current.
The MIC2174/MIC2174C implements an internal digital
soft-start by making the 0.8V reference voltage V REF
ramp from 0 to 100% in about 6ms with a 9.7mV step.
Therefore, the output voltage is controlled to increase
slowly by a stair-case V REF ramp. Once the soft-start
cycle ends, the related circuitry is disabled to reduce
current consumption. V IN must be powered up no earlier
than V HSD to make the soft-start function behavior
correctly.
Current Limit
The MIC2174/MIC2174C uses the R DS(ON) of the low-
side power MOSFET to sense over-current conditions.
This method will avoid adding cost, board space and
power losses taken by a discrete current sense resistor.
The low-side MOSFET is used because it displays much
lower parasitic oscillations during switching than the
high-side MOSFET.
In each switching cycle of the MIC2174/MIC2174C
converter, the inductor current is sensed by monitoring
the low-side MOSFET in the OFF period. The sensed
voltage is compared with a current-limit threshold
voltage V CL after a blanking time of 150ns. If the sensed
voltage is over V CL , which is 130mV typical at 0.8V
feedback voltage, then the MIC2174/MIC2174C turns off
the high-side MOSFET and a soft-start sequence is
triggered. This mode of operation is called “hiccup
mode” and its purpose is to protect the downstream load
in case of a hard short. The current limit threshold V CL
has a fold back characteristic related to the FB voltage.
Please refer to the “Typical Characteristics” for the curve
of V CL vs. FB voltage.
September 2010
12
M9999-091310-C
相关PDF资料 |
PDF描述 |
|---|---|
| EBA36DTMD | CONN EDGECARD 72POS R/A .125 SLD |
| 2727-20J | INDUCTOR TOROID 390UH SHIELD RAD |
| EBA36DTBN | CONN EDGECARD 72POS R/A .125 SLD |
| ADM691AARN-REEL7 | IC SUPERVISOR MPU 4.65V 16SOIC |
| 2727-19J | INDUCTOR TOROID 330UH SHIELD RAD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2176-1 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Wide Input Voltage, Synchronous Buck Controllers Featuring Adaptive On-Time Control |
| MIC2176-1YMM | 功能描述:DC/DC 开关控制器 76V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2176-1YMM TR | 功能描述:DC/DC 开关控制器 76V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2176-2 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Wide Input Voltage, Synchronous Buck Controllers Featuring Adaptive On-Time Control |
| MIC2176-2YMM | 功能描述:DC/DC 开关控制器 76V Synchronous Buck Controller RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。