- 您现在的位置：买卖IC网 > PDF目录14491 > MIC2177-3.3YWM TR (Micrel Inc)IC REG BUCK SYNC 3.3V 20SOIC PDF资料下载
参数资料
| 型号： | MIC2177-3.3YWM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 10/15页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC 3.3V 20SOIC |
| 标准包装： | 1 |
| 类型： | 降压（降压） |
| 输出类型： | 固定 |
| 输出数： | 1 |
| 输出电压： | 3.3V |
| 输入电压： | 4.5 V ~ 16.5 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 200kHz |
| 电流 - 输出： | 2.5A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 标准包装 |
| 供应商设备封装： | 20-SOIC（宽型） |
| 产品目录页面： | 1092 (CN2011-ZH PDF) |
| 其它名称： | 576-1542-6 |
Micrel, Inc.
given in the “Applications Information” section. Note that
? I L varies as a function of input voltage, and this also
causes I MIN to vary. In applications where the input
voltage changes by a factor of two, I MIN will typically vary
from 130mA to 250mA.
During low-dropout operation, the minimum current
thresh-old circuit reduces the minimum value of I L1(peak)
for PWM operation. This compensates for ? I L1
decreasing to almost zero when the difference between
V IN and V OUT is very low.
Changing from Skip to PWM Mode
The MIC2177 will automatically change from skip to
PWM mode when I LOAD exceeds 300mA. During skip-
mode operation, it can supply up to 300mA, and when
I LOAD exceeds this limit, V OUT will fall below its nominal
value. At this point, the MIC2177 begins operating in
PWM mode. Note that the maximum value of I LOAD for
skip mode is greater than the minimum value required
for PWM mode. This current hysteresis prevents the
MIC2177 from toggling between modes when I LOAD is in
the range of 100mA to 300mA.
MIC2177
The low output comparator determines when V OUT is low
enough for the regulator to change operating modes. It
detects when the feedback voltage is 3% below nominal,
and pulls the AUTO pin to ground. When AUTO is less
than 1.6V, the PWM/skip-mode select logic places the
MIC2177 into PWM operation. The external 2.2nF
capacitor connected to AUTO is charged by a 10μA
current source after the regulator begins operating in
PWM mode. As a result, AUTO stays below 1.6V for
several switching cycles after PWM operation begins,
forcing the MIC2177 to remain in PWM mode during this
transition.
External PWM-Mode Selection
The MIC2177 can be forced to operate in only PWM
mode by connecting AUTO to ground. This prevents
skip-mode operation in applications that are sensitive to
switching noise.
April 2008
10
M9999-042108
相关PDF资料 |
PDF描述 |
|---|---|
| MAX752CWE+ | IC REG BOOST ADJ 0.2A 16SOIC |
| LGN2C222MELC35 | CAP ALUM 2200UF 160V 20% SNAP |
| MAX17067EUA+ | IC REG BOOST ADJ 0.3A 8UMAX |
| MAX17083ETG+ | IC REG BUCK ADJ 5A 24TQFN |
| ECC35DRTH | CONN EDGECARD 70POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2177-5.0BWM | 功能描述:直流/直流开关调节器 2.5A 200kHz Synchronous Switcher RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2177-5.0BWM TR | 功能描述:直流/直流开关调节器 2.5A 200kHz Synchronous Switcher RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2177-5.0BWMTR | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
| MIC2177-5.0YWM | 功能描述:直流/直流开关调节器 2.5A 200kHz Synchronous Switcher RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| MIC2177-5.0YWM TR | 功能描述:直流/直流开关调节器 2.5A 200kHz Synchronous Switcher RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。