参数资料
| 型号： | MIC2182YSM |
| 厂商： | Micrel Inc |
| 文件页数： | 18/28页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SSOP |
| 标准包装： | 77 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 330kHz |
| 占空比： | 86% |
| 电源电压： | 4.5 V ~ 32 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SSOP（0.209"，5.30mm 宽） |
| 包装： | 管件 |
| 产品目录页面： | 1092 (CN2011-ZH PDF) |
| 其它名称： | 576-1069 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
MIC2182
For the low-side switch (N-channel MOSFET), the dc power
dissipation is:
P switch2(dc) = R DS(on)2 × I SW 2 (rms) 2
Since the ac switching losses for the low side MOSFET is
near zero, the total power dissipation is:
P low-side MOSFET(max) = P switch2(dc)
The total power dissipation for the high-side MOSFET is:
P highsideMOSFET(max) = P SWITCH 1(dc) + P AC
External Schottky Diode
An external freewheeling diode is used to keep the inductor
current flow continuous while both MOSFETs are turned off.
This dead time prevents current from flowing unimpeded
through both MOSFETs and is typically 80ns The diode
conducts twice during each switching cycle. Although the
average current through this diode is small, the diode must be
able to handle the peak current.
I D(avg) = I OUT × 2 × 80ns × f S
Micrel
circuit inductance will cause ringing during the high-side
MOSFET turn-on.
An external Schottky diode conducts at a lower forward
voltage preventing the body diode in the MOSFET from
turning on. The lower forward voltage drop dissipates less
power than the body diode. The lack of a reverse recovery
mechanism in a Schottky diode causes less ringing and less
power loss. Depending on the circuit components and oper-
ating conditions, an external Schottky diode will give a 1/2%
to 1% improvement in efficiency. Figure 12 illustrates the
difference in noise on the VSW pin with and without a
Schottky diode.
Output Capacitor Selection
The output capacitor values are usually determined by the
capacitors ESR (equivalent series resistance). Voltage rating
and RMS current capability are two other important factors in
selecting the output capacitor. Recommended capacitors are
tantalum, low-ESR aluminum electrolytics, and OS-CON.
The output capacitor ’ s ESR is usually the main cause of
output ripple. The maximum value of ESR is calculated by:
The reverse voltage requirement of the diode is:
V diode (rrm) = V IN
The power dissipated by the Schottky diode is:
R ESR ≤
where:
? V OUT
I PP
P diode = I D(avg) × V F
where:
V F = forward voltage at the peak diode current
V OUT = peak to peak output voltage ripple
I PP = peak to peak inductor ripple current
The total output ripple is a combination of the ESR and the
output capacitance. The total ripple is calculated below:
The external Schottky diode, D2, is not necessary for circuit
operation since the low-side MOSFET contains a parasitic
body diode. The external diode will improve efficiency and
decrease high frequency noise. If the MOSFET body diode is
? V OUT =
? I PP × (1 ? D) ?
? ?
? C OUT × f S ?
2
+ ( I PP × R ESR
) 2
used, it must be rated to handle the peak and average current.
The body diode has a relatively slow reverse recovery time
and a relatively high forward voltage drop. The power lost in
the diode is proportional to the forward voltage drop of the
diode. As the high-side MOSFET starts to turn on, the body
diode becomes a short circuit for the reverse recovery period,
dissipating additional power. The diode recovery and the
where:
D = duty cycle
C OUT = output capacitance value
f S = switching frequency
The voltage rating of capacitor should be twice the output
voltage for a tantalum and 20% greater for an aluminum
electrolytic or OS-CON.
The output capacitor RMS current is calculated below:
I C
OUT
(rms) =
I PP
12
The power dissipated in the output capacitor is:
P DISS(C
OUT )
= I C
OUT
(rms) 2 × R ESR(C
OUT )
Input Capacitor Selection
The input capacitor should be selected for ripple current
rating and voltage rating. Tantalum input capacitors may fail
when subjected to high inrush currents, caused by turning the
input supply on. Tantalum input capacitor voltage rating
TIME
Figure 12. Switch Output Noise
With and Without Shottky Diode
should be at least 2 times the maximum input voltage to
maximize reliability. Aluminum electrolytic, OS-CON, and
multilayer polymer film capacitors can handle the higher
inrush currents without voltage derating.
M9999-042204
18
April 22, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3853EUJ#TRPBF | IC REG CTRLR BUCK PWM CM 40-QFN |
| LT1619ES8#PBF | IC REG CTRLR PWM CM 8-SOIC |
| ABC13DRXI-S734 | CONN EDGECARD 26POS DIP .100 SLD |
| ABC17DRTH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| LTC3851EUD#PBF | IC REG CTRLR BUCK PWM CM 16-QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2182YSM TR | 功能描述:DC/DC 开关控制器 High EfficiencySynchronous Buck Controller SSOP Pkg (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2182YSM-TR | 功能描述:Buck Regulator Positive Output Step-Down DC-DC Controller IC 16-SSOP 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:停产 输出类型:晶体管驱动器 功能:降压 输出配置:正 拓扑:降压 输出数:1 输出阶段:1 电压 - 电源（Vcc/Vdd）:4.5 V ~ 32 V 频率 - 开关:300kHz 占空比（最大）:0.86 同步整流器:是 时钟同步:是 串行接口:- 控制特性:使能，软启动 工作温度:-40°C ~ 85°C（TA） 封装/外壳:16-SSOP（0.209"，5.30mm 宽） 供应商器件封装:16-SSOP 标准包装:1 |
| MIC2183 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Synchronous Buck PWM Control IC Final Information |
| MIC2183_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:Low Voltage Synchronous Buck PWM Control IC |
| MIC2183BM | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。