- 您现在的位置：买卖IC网 > PDF目录15113 > MIC2186BM TR (Micrel Inc)IC REG CTRLR BST FLYBK CM 16SOIC PDF资料下载
参数资料
| 型号： | MIC2186BM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 13/15页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST FLYBK CM 16SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 85% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 无 |
| 升压： | 是 |
| 回扫： | 是 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2186BMTR MIC2186BMTR-ND |
MIC2186
MIC2186 Sync
Micrel, Inc.
output capacitance. Slowing the output risetime lowers the
input surge current. Soft start may also be used for power
Conditions:
HiDC = HIGH
F/2 = LOW
Conditions:
HiDC = LOW
F/2 = LOW
Figure 8a.
MIC2186 Sync
Sync Input
(Pin 11)
Gat Drive Output
(Pin 14)
Sync Input
(Pin 11)
Gat Drive Output
(Pin 14)
supply sequencing. The soft start cannot control the initial
surge in current in a boost converter when Vin is applied. This
surge current is caused by the output capacitance charging
up to the input voltage. The current flows from the input
through the inductor and output diode to the output capaci-
tors.
The soft start voltage is applied directly to the PWM compara-
tor. A 5uA internal current source is used to charge up the soft
start capacitor. Either of 2 UVLO conditions will pull the soft
start capacitor low.
* When the Vdd voltage drops below its UVLO
threshold
* When the enable pin drops below its 1.5V UVLO
threshold
The part switches at a low duty cycle when the soft start pin
voltage zero. As the soft start voltage rises from 0V to 0.7V,
the duty cycle increases from the minimum duty cycle to the
operating duty cycle. The oscillator runs at the foldback
frequency until the feedback voltage rises above 0.3V. In a
boost converter the output voltage is equal to the input
voltage before the MIC2186 starts switching. If the ratio of
Vout/Vin is low, the voltage on the feedback pin will already
be greater than 0.3V and the converter begin switching at the
selected operating frequency.
The risetime of the output is dependent on the soft start
Figure 8b.
The maximum recommended output switching frequency is
600kHz. Synchronizing to higher frequencies may be pos-
sible, however there are some concerns. As the switching
frequency is increased, the switching period decreases. The
minimum on-time in the MIC2186 becomes a greater part of
the total switching period. This may prevent proper operation
as Vin approaches Vout and may also minimize the effective-
ness of the current limit circuitry. The maximum duty cycle
decreases as the sync frequency is increased. Figure 9
shows the relationship between the minimum/maximum duty
cycle and frequency.
Max. Duty Cycle
vs. Frequency
85
capacitor, output capacitance, input and output voltage and
load current. The scope photo in Figure 10 show the output
voltage and the soft start pin voltage at startup. The output
voltage is initially at the input voltage less a diode drop. After
the converter is enabled the output slowly rises due to the
minimum duty cycle of the controller. As the soft start voltage
increases, the output voltage rises in a controlled fashion until
the output voltage reaches the regulated value.
Soft Start
50 F/2=H
80
75 HiDC=H
F/2=H
70
65
60
55
HiDC=L
45
HiDC=H
F/2=L
HiDC=L
F/2=L
Figure 10.
0V
40
250 300 350 400 450 500 550 600
SYNC FREQUENCY (kHz)
Figure 9.
Soft start
Soft start reduces the power supply input surge current at
start up by limiting the output voltage risetime. Input surge
current occurs when the boost converter charges up the
Voltage Setting Components
The MIC2186 requires two resistors to set the output voltage
as shown in figure 11
April 2005
13
M9999-042205
相关PDF资料 |
PDF描述 |
|---|---|
| ESC10DRTH-S734 | CONN EDGECARD 20POS DIP .100 SLD |
| EMC08DRTH-S734 | CONN EDGECARD 16POS DIP .100 SLD |
| VE-24V-EW-F1 | CONVERTER MOD DC/DC 5.8V 100W |
| ESC07DREF-S734 | CONN EDGECARD 14POS .100 EYELET |
| GCM30DTAT | CONN EDGECARD 60POS R/A .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2186BQS | 功能描述:IC REG CTRLR BST FLYBK CM 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2186BQS TR | 功能描述:IC REG CTRLR BST FLYBK CM 16QSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| MIC2186YM | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2186YM TR | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2186YQS | 功能描述:DC/DC 开关控制器 SO-16 Low Vin Synchronous Buck PWM Control IC (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。