- 您现在的位置：买卖IC网 > PDF目录15113 > MIC2194BM TR (Micrel Inc)IC REG CTRLR BST PWM CM 8-SOIC PDF资料下载
参数资料
| 型号： | MIC2194BM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 7/10页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BST PWM CM 8-SOIC |
| 标准包装： | 2,500 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 440kHz |
| 占空比： | 100% |
| 电源电压： | 2.9 V ~ 14 V |
| 降压： | 是 |
| 升压： | 是 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2194BMTR MIC2194BMTR-ND |
R SENSE =
MIC2194
The MIC2194 controller is broken down into several func-
tions.
? Control loop
? PWM operation
? Current mode control
? Current limit
? Reference, enable and UVLO
? MOSFET gate drive
? Oscillator
Control Loop
PWM Control Loop
Micrel
Current Limit
The output current is detected by the voltage drop across the
external current sense resistor (R SENSE in Figure 1.). The
current sense resistor must be sized using the minimum
current limit threshold. The external components must be
designed to withstand the maximum current limit. The current
sense resistor value is calculated by the equation below:
MIN _ CURRENT _ SENSE _ THRESHOLD
I OUT _ MAX
The maximum output current is:
The MIC2194 uses current mode control to regulate the
output voltage. This dual control loop method (illustrated in
I OUT _ MAX =
MAX _ CURRENT _ SENSE _ THRESHOLD
R SENSE
Figure 2) senses the output voltage (outer loop) and the
inductor current (inner loop). It uses inductor current and
output voltage to determine the duty cycle of the buck
converter. Sampling the inductor current effectively removes
the inductor from the control loop, which simplifies compen-
sation.
V IN
The current sense pins VIN (pin 8) and CSL (pin 4) are noise
sensitive due to the low signal level, high input impedance
and input ripple voltage. The PCB traces should be short and
routed close to each other. A 0.1 μ F capacitor across the pins
will attenuate high frequency switching noise.
When the peak inductor current exceeds the current limit
threshold, the overcurrent comparator turns off the high-side
Switching
Converter
Switch
I INDUCTOR
V OUT
Voltage
Divider
MOSFET for the remainder of the switching cycle, effectively
decreasing the duty cycle. The output voltage drops as
additional load current is pulled from the converter. When the
voltage at the feedback pin (FB) reaches approximately 0.3V,
the circuit enters frequency foldback mode and the oscillator
frequency will drop to 1/4 of the switching frequency. This
limits the maximum output power delivered to the load under
Driver
V ERROR
V REF
a short circuit condition.
Reference, Enable and UVLO Circuits
I INDUCTOR
V ERROR
t ON
t PER
D = t ON /t PER
Figure 2. Current Mode Control Example
As shown in Figure 1, the inductor current is sensed by
measuring the voltage across the resistor, R SENSE . A ramp is
added to the amplified current sense signal to provide slope
compensation, which is required to prevent unstable opera-
tion at duty cycles greater than 50%.
A transconductance amplifier is used for the error amplifier,
which compares an attenuated sample of the output voltage
with a reference voltage. The output of the error amplifier is
the compensation pin (COMP), which is compared to the
current sense waveform in the PWM block. When the current
signal becomes greater than the error signal, the comparator
turns off the high side drive. The COMP pin provides access
to the output of the error amplifier and allows the use of
external components to stabilize the voltage loop.
The output drivers are enabled when the following conditions
are satisfied:
? The V DD voltage (pin 5) is greater than its
undervoltage threshold.
? The voltage on the enable pin (pin 3) is greater
than the enable UVLO threshold.
The enable pin (pin 3) has two threshold levels, allowing the
MIC2194 to shut down in a low current mode, or turn off output
switching in standby mode. An enable pin voltage lower than
the shutdown threshold turns off all the internal circuitry and
places the MIC2194 in a micropower shutdown mode.
If the enable pin voltage is between the shutdown and
standby thresholds, the internal bias, V DD and reference
voltages are turned on. The output drivers are inhibited from
switching. The OUTP pin is in a high state. Raising the enable
voltage above the standby threshold enables the output
driver. The standby threshold is specified in the electrical
characteristics. A resistor divider can be used with the enable
pin to prevent the power supply from turning on until a
specified input voltage is reached. The circuit in Figure 3
shows how to connect the resistors.
April 2005
7
MIC2194
相关PDF资料 |
PDF描述 |
|---|---|
| RBC17DRYN-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| RCM22DTAS | CONN EDGECARD 44POS R/A .156 SLD |
| RBC17DRYH-S734 | CONN EDGECARD 34POS DIP .100 SLD |
| MIC2194BM | IC REG CTRLR BST PWM CM 8-SOIC |
| RCC13DRTI-S734 | CONN EDGECARD 26POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2194YM | 功能描述:DC/DC 开关控制器 SO-8 3V Buck Contoller (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2194YM TR | 功能描述:DC/DC 开关控制器 SO-8 3V Buck Contoller (Lead Free) RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MIC2196 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:400kHz SO-8 Boost Control IC |
| MIC2196_08 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:400kHz SO-8 Boost Control IC |
| MIC2196BM | 功能描述:IC REG CTRLR BST FLYBK PWM 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。